RunRyder RC
Refresh Screen

Top 10-22-2019 07:04 PM
Bottom 10-15-2019 07:04 PM

9 topic posts for  Keygrigger   or all topics

Subscriptions   View Classifieds   View Off Topics   View New Posts   Topics Low Replies

08-10-2015 02:44 AM  4 years ago
TopicTopic StarterReplyViewLast Post
 Docs  •••Scale Heli Scale Helicopter Main Discussion
Airwolf Turbine - My Build 📷 ( page 1 2 3 4 ... Last page )
ssmith512 493 41890 08-09-2017 01:47 AM
Heli143
Keygrigger

rrVeteran

Mississauga, Ont. Canada

Congrats Steve. I didn't see you after the presentation but look forward to Dalton. See you there.

Don
 

08-31-2015 04:28 AM  4 years ago
TopicTopic StarterReplyViewLast Post
 Docs  •••Scale Heli Scale Helicopter Main Discussion
Airwolf Turbine - My Build 📷 ( page 1 2 3 4 ... Last page )
ssmith512 493 41890 08-09-2017 01:47 AM
Heli143
Keygrigger

rrVeteran

Mississauga, Ont. Canada

Oh, there might be one or two there that have read a thing or two about a turbine installation

Don
 

10-01-2015 02:42 AM  4 years ago
TopicTopic StarterReplyViewLast Post
 Docs  •••Scale Heli Scale Helicopter Main Discussion
Airwolf Turbine - My Build 📷 ( page 1 2 3 4 ... Last page )
ssmith512 493 41890 08-09-2017 01:47 AM
Heli143
Keygrigger

rrVeteran

Mississauga, Ont. Canada

Steve, I have had my moments like that more times than I can count. I think I tore the TOW sight front glass off twice before I remembered to install all the items that had to go inside in order to let it swivel and remain locked in place. Yes, cutting an access hole is not such a bad thing and will give you a spot in the future that you can get at it, if needed. I see you planned that it would be on the bottom so the repair would never be seen. Nice job.

Don
 

10-11-2015 01:40 AM  4 years ago
TopicTopic StarterReplyViewLast Post
 Docs  •••Scale Heli Scale Helicopter Main Discussion
Airwolf Turbine - My Build 📷 ( page 1 2 3 4 ... Last page )
ssmith512 493 41890 08-09-2017 01:47 AM
Heli143
Keygrigger

rrVeteran

Mississauga, Ont. Canada

Nice work. Keep it up.

Don
 

12-06-2015 10:19 PM  3 years ago
TopicTopic StarterReplyViewLast Post
 Docs  •••Scale Heli Scale Helicopter Main Discussion
Airwolf Turbine - My Build 📷 ( page 1 2 3 4 ... Last page )
ssmith512 493 41890 08-09-2017 01:47 AM
Heli143
Keygrigger

rrVeteran

Mississauga, Ont. Canada

I bet you were hoping your shorts didn't fill up when you started those holes. Nice reworking of the tail surfaces and exhaust holes. It is pretty much time to start mine. Take care.

Don
 

01-14-2016 06:52 PM  3 years ago
TopicTopic StarterReplyViewLast Post
 Docs  •••Scale Heli Scale Helicopter Main Discussion
Airwolf Turbine - My Build 📷 ( page 1 2 3 4 ... Last page )
ssmith512 493 41890 08-09-2017 01:47 AM
Heli143
Keygrigger

rrVeteran

Mississauga, Ont. Canada

The doors look very good and the Metal Airwolf rocks. Well done.

Don
 

03-03-2016 04:05 PM  3 years ago
TopicTopic StarterReplyViewLast Post
 Docs  •••Scale Heli Scale Helicopter Main Discussion
Airwolf Turbine - My Build 📷 ( page 1 2 3 4 ... Last page )
ssmith512 493 41890 08-09-2017 01:47 AM
Heli143
Keygrigger

rrVeteran

Mississauga, Ont. Canada

Well done. If I could make a suggestion as to the permanency of the winglets, when I was at the stage of gluing the horizontal surfaces for my CH-139, I used Shoe-Goo rather than epoxy or CA. There was more than enough gripping area on the stubs for the glue to adhere to and since in yours, there is a structure that will help to hold it from drooping, a couple of well placed glue lines will hold it in place. This will allow their removal in the event of repairs being needed for anything internal that might only be accessible with the winglets off (landing gear, machinegun system). Ultimately, it's up to you. Those vents and fitting of the upper to the main doghouse look very, very nice. I can tell you from building an Airwolf doghouse for a 600 size, that the screen angles will give you some fun. Take care.

Don
 

01-02-2017 01:38 AM  34 months ago
TopicTopic StarterReplyViewLast Post
 Docs  •••Scale Heli Scale Helicopter Main Discussion
Airwolf Turbine - My Build 📷 ( page 1 2 3 4 ... Last page )
ssmith512 493 41890 08-09-2017 01:47 AM
Heli143
Keygrigger

rrVeteran

Mississauga, Ont. Canada

Steve, you're cut off from Christmas specials next year.

Don
 

06-30-2017 08:51 PM  28 months ago
TopicTopic StarterReplyViewLast Post
 Docs  •••Scale Heli Scale Helicopter Main Discussion
Airwolf Turbine - My Build 📷 ( page 1 2 3 4 ... Last page )
ssmith512 493 41890 08-09-2017 01:47 AM
Heli143
Keygrigger

rrVeteran

Mississauga, Ont. Canada

Hi Steve. Happened to me, too. Once I had five forums downloading content from Photobucket and the bandwidth was way higher than the monthly limit. Now, I only use the forum's posting storage and have not looked at PB for three years now. I said the same thing, only with a few more explicatives thrown in for good measure. Take care.

Don
 
🏠Home View New

Tuesday, October 22 - 7:04 pm - Copyright © 2000-2019 RunRyder   EMAILEnable Cookies

Login Here
 New Subscriptions 
 Buddies Online