Help with Ikon2 connections

rrTV-PHOTO GALLERIES MY GALLERY HELP-FAQ

myHOME PM pmRR MEMBERS 378 ONLINE 3 EVENTS SEARCH REGISTER START HERE

WATCH

1 page 80 views

Post Reply

RunRyder	RunRyder

Home › RC & Power › ✈️Aircraft › 🚁Helicopter › Flybarless Rotor Head Systems › Brain iKon › Help with Ikon2 connections

12-10-2020 05:16 AM 5 months ago

Topic Vote

0Post 1

Pete0055

rrNewbie

Minneapolis, MN

MyPosts All Forum Topic

Help with Ikon2 connections

I have a 550x and it comes with the align BLE-100 amp ESC....there are two wires with theee leads coming from the ESC....I have plugged the red/black/white wire into Ch 1 to control the throttle...there is a lead with a red/black wire and a lead with a yellow wire....where do I plug these into the Ikon and which pins are they seeing when plugged in?

SHARE PM EMAIL Attn:RR Quote

12-10-2020 05:47 AM 5 months ago

1Post 2

JLF92677

rrApprentice

Southern California

MyPosts All Forum Topic

Pete0055 there is a lead with a red/black wire and a lead with a yellow wire....where do I plug these into the Ikon

Yellow wire lead is RPM sensor signal wire, so plug it into iKon GOV signal input port (yellow wire to top pin assignment.) Red/black wire lead is BEC output wire so plug it into receiver BAT port or any unused receiver channel port or unused iKon channel port for better power supply to iKon and servos.

SHARE PM EMAIL GALLERY Attn:RR Quote

12-10-2020 06:22 AM 5 months ago

0Post 3

Pete0055

rrNewbie

Minneapolis, MN

MyPosts All Forum Topic

Ok thank you....I’m not using a receiver....just two spektrum satellites....

SHARE PM EMAIL Attn:RR Quote

12-10-2020 06:25 AM 5 months ago

0Post 4

Pete0055

rrNewbie

Minneapolis, MN

MyPosts All Forum Topic

Does the yellow wire go to the signal pin?

I’m assuming the BEC red/brown goes to the +/- pins?

SHARE PM EMAIL Attn:RR Quote

12-10-2020 07:19 AM 5 months ago

0Post 5

JLF92677

rrApprentice

Southern California

MyPosts All Forum Topic

Pete0055 Ok thank you....I’m not using a receiver....just two spektrum satellites....

Ok, plug Red/black wire BEC output lead to any unused iKon channel port for better power supply to iKon and servos.

SHARE PM EMAIL GALLERY Attn:RR Quote

12-10-2020 07:24 AM 5 months ago

0Post 6

JLF92677

rrApprentice

Southern California

MyPosts All Forum Topic

Pete0055 Does the yellow wire go to the signal pin?

Yes

Pete0055 I’m assuming the BEC red/brown goes to the +/- pins?

Yes

SHARE PM EMAIL GALLERY Attn:RR Quote

12-10-2020 08:21 AM 5 months ago

0Post 7

rik

rrNovice

Italy

MyPosts All Forum Topic

You can also remove the yellow wire contact from the plastic connector (just lift the plastic fixing tab) and insert it into the free hole of the plastic connector that carries the second output of the BEC (connector with only black and red wires) and then insert this single three-wire connector into the GOV connector of the Brain2. In this way the connectors and connections are lower, simpler and cleaner and do not occupy any other connector of the Brain2.https://www.msh-electronics.com

SHARE PM EMAIL HOMEPAGE GALLERY Attn:RR Quote

WATCH

1 page 80 views

Post Reply

RunRyder	RunRyder

Home › RC & Power › ✈️Aircraft › 🚁Helicopter › Flybarless Rotor Head Systems › Brain iKon › Help with Ikon2 connections

Print TOPIC

3 Topic Subscribe

New Subscriptions

Buddies Online