RunRyder RC
WATCH
 1 page 188 views Post Reply
07-11-2020 04:48 PM  75 days ago
Topic Vote0Post 1
mirmanchuck

rrApprentice

Venice Fl.

MyPosts All Forum Topic
Servo movement
Setting up ikon2 and servos move when plugged in but nothing after that. They center and won’t move again. Have setup proper frequency for servos. In servo reversing tab They center and won’t move after that. How can I fix this?
SpectraG/3Dmax
Trex600esp BeastX DFC
QAV500G Multirotor
SHARE  PM  EMAIL  GALLERY  Attn:RR  Quote
07-12-2020 12:44 AM  75 days ago
Rojoalfa

rrKey Veteran

Punta de Mata, Monagas-Venezuela

MyPosts All Forum Topic
/
/

Are you sure you bind your receiver?

Futaba fasst mult? 7ch? Fasstest, fhss, spektrum?

/
Saludos cordiales,
SHARE  PM  EMAIL  GALLERY  Attn:RR  Quote
07-12-2020 04:46 PM  74 days ago
mirmanchuck

rrApprentice

Venice Fl.

MyPosts All Forum Topic
I am using two spektrum satellites and they are working fine.SpectraG/3Dmax
Trex600esp BeastX DFC
QAV500G Multirotor
SHARE  PM  EMAIL  GALLERY  Attn:RR  Quote
07-12-2020 05:41 PM  74 days ago
Steve.Favorite

rrVeteran

Brookville, Ohio

MyPosts All Forum Topic
Its been a while since I messed with IKON FBL units, however how are your Dual rates and expo values set up?
SHARE  PM  EMAIL  GALLERY  Attn:RR  Quote
07-12-2020 06:19 PM  74 days ago
mirmanchuck

rrApprentice

Venice Fl.

MyPosts All Forum Topic
Everything works fine in the receiver tab.SpectraG/3Dmax
Trex600esp BeastX DFC
QAV500G Multirotor
SHARE  PM  EMAIL  GALLERY  Attn:RR  Quote
07-12-2020 06:52 PM  74 days ago
Steve.Favorite

rrVeteran

Brookville, Ohio

MyPosts All Forum Topic
you chose the correct satellite, checked the Bind check box and bound the sats?
SHARE  PM  EMAIL  GALLERY  Attn:RR  Quote
07-12-2020 06:54 PM  74 days ago
Steve.Favorite

rrVeteran

Brookville, Ohio

MyPosts All Forum Topic
are you using RJX or BK servos?
SHARE  PM  EMAIL  GALLERY  Attn:RR  Quote
07-13-2020 01:08 AM  74 days ago
mirmanchuck

rrApprentice

Venice Fl.

MyPosts All Forum Topic
Align ds510 setup in servo tab to correct frequency.SpectraG/3Dmax
Trex600esp BeastX DFC
QAV500G Multirotor
SHARE  PM  EMAIL  GALLERY  Attn:RR  Quote
07-13-2020 03:07 AM  74 days ago
Rojoalfa

rrKey Veteran

Punta de Mata, Monagas-Venezuela

MyPosts All Forum Topic
mirmanchuck I am using two spektrum satellites and they are working fine.
/
/

They are working fine...
How do you know?
Servos doesn't move!!!

If your Tx+receiver are working OK, then Your ikon is faulty...

/
Saludos cordiales,
SHARE  PM  EMAIL  GALLERY  Attn:RR  Quote
07-13-2020 03:43 AM  74 days ago
Steve.Favorite

rrVeteran

Brookville, Ohio

MyPosts All Forum Topic
Could you post a video of the Heli and the software while you are trying to move the servos?
SHARE  PM  EMAIL  GALLERY  Attn:RR  Quote
07-13-2020 04:40 AM  74 days ago
Girard Ibanez

rrVeteran

Tucson, Arizona (formally from Guam)

MyPosts All Forum Topic
💎Sustaining Member
Verify you are using the correct receiver protocol?

Are you using a Spektrum Receiver in addition to the Ikon?

To many variables unless you post your components.

Here's my Thoughts;

Spektrum Rx connected to Ikon2 on SRXL bus line.

Ikon2 software selection protocol "SRXL MULTIplex".

Spektrum satellites connected to Ikon2.

Ikon2 software Receiver Page, check the box for binding lower bottom of page.

You need to SIMULTANEOUSLY bind the Spektrum receiver and Ikon2 to the transmitter.

If both Spektrum receiver and Spektrum satellites on Ikon2 are binded the Orange LEDs will be a steady on. Not binded they will blink.

Team Thunder Tiger
since 6/2005 to 12/2014
SHARE  PM  EMAIL  GALLERY  Attn:RR  Quote
07-13-2020 04:43 AM  74 days ago
rik

rrNovice

Italy

MyPosts All Forum Topic
Please, can you send your configuration file (mtr extension).
Go to "File" menu on top left, select "Save config to file ..." and attach to a new post.
Thanks
https://www.msh-electronics.com
SHARE  PM  EMAIL  HOMEPAGE  GALLERY  Attn:RR  Quote
07-13-2020 04:40 PM  73 days ago
mirmanchuck

rrApprentice

Venice Fl.

MyPosts All Forum Topic
SpectraG/3Dmax
Trex600esp BeastX DFC
QAV500G Multirotor
SHARE  PM  EMAIL  GALLERY  Attn:RR  Quote
07-14-2020 01:01 AM  73 days ago
Steve.Favorite

rrVeteran

Brookville, Ohio

MyPosts All Forum Topic
What I'm seeing online is the ds510's are either 333 or 200mhz, can you select 200mhz in the freq slide bar, to test?
SHARE  PM  EMAIL  GALLERY  Attn:RR  Quote
07-16-2020 09:30 PM  70 days ago
mirmanchuck

rrApprentice

Venice Fl.

MyPosts All Forum Topic
I tried 333 and 200. No response. They center when entering cyclic config tab but no response after they center.SpectraG/3Dmax
Trex600esp BeastX DFC
QAV500G Multirotor
SHARE  PM  EMAIL  GALLERY  Attn:RR  Quote
07-24-2020 07:26 AM  63 days ago
rik

rrNovice

Italy

MyPosts All Forum Topic
@mirmanchuck
Hi.
I see you never sent the configuration file that I suggested you send and explained how to do it.
For this reason, I guess you've already solved your problems in the meantime.
Can you confirm so that we can consider the matter closed?
Thank you.
https://www.msh-electronics.com
SHARE  PM  EMAIL  HOMEPAGE  GALLERY  Attn:RR  Quote
WATCH
 1 page 188 views Post Reply
Print TOPIC

 3  Topic Subscribe

Friday, September 25 - 12:27 pm - Copyright © 2000-2020 RunRyder   EMAILEnable Cookies

Login Here
 New Subscriptions 
 Buddies Online