RunRyder RC
WATCH
 2 pages [ <<    <     1     ( 2 )    >    >> ] 682 views POST REPLY
HomeScale✈️AircraftScale HeliVario Scale Helicopters › Vario 1:6th "Big" Jet Ranger
02-02-2020 03:57 PM  14 days ago
X-Cell Man

rrNovice

Haubstadt, IN - USA

MyPosts All Forum Topic
Yes Mr. Cheesehead ( I think he has one too) is coming along real good( damn it hehe)!!!
I'm redoing my fins on both of my Jet Rangers. Between looking at the photos and the models. Also sitting back looking at them. Just not quite looking right. Back to the drawing board.
Sooner or later I may get them both done.
Keep it up Mike and the rest of you. It keeps me working harder on these .

Dan
SHARE  PM  EMAIL  Attn:RR  Quote
02-03-2020 03:09 PM  13 days ago
Grimracer

rrKey Veteran

Eau Claire WI

MyPosts All Forum Topic
Thanks guys...

I have the servo tray painted and the all that "jaz" ready to install. I am going to re-locate the throttle servo (3070HV) tho..

The Futaba H700s (SERVO BEAST!!) are a tick larger then servos of old.. so.. I have to sneak out a bit of the plate for that one. One nice thing about the new servos is they have longer servo leads. If i play my cards right I will not need any extensions to make it all work.. Its looking like the 760 will be trayed behind the anti rotation loop.. I can simply remove the aft cover to allow access.

Anyhow.. back to making babys.. (no.. you dont want to know)

Grim
Michael J Zaborowski
Futaba USA
AMA 124909
IRCHA 5453
SHARE  PM  EMAIL  GALLERY  Attn:RR  Quote
02-07-2020 01:08 PM  9 days ago
Grimracer

rrKey Veteran

Eau Claire WI

MyPosts All Forum Topic
Well.. the good the bad and the UgLy..

I wanted to move my throttle servo off the fuse.. so I designed this mount..

then I wanted to machine this mount..

Then i put THE FIRST HOLE in my machine bed after 16 years of owning the machine..

Then I mounted the part on the heli.

And once again.. the world is aligned.. with a FRICKING HOLE IN MY MACHINE BED....LOL..

O well.. LOL.. do ya think some JB Weld and no body will see it.. WAIT.. i cannot be around JB Weld.. CRIPES.. I can not WIN!

Grim

Michael J Zaborowski
Futaba USA
AMA 124909
IRCHA 5453
SHARE  PM  EMAIL  GALLERY  Attn:RR  Quote
02-07-2020 11:30 PM  9 days ago
X-Cell Man

rrNovice

Haubstadt, IN - USA

MyPosts All Forum Topic
Hey Mike,
You and the Missus just get in the Yellow mobile and bring it along down here and I will mix some up for you. Bring your pod and boom machine with you and we will shoot dollar ($$) autos. While the JB Weld is drying. Later have some Captain and beers.
Remember I-64 exit 18 go south hehe

Dan
SHARE  PM  EMAIL  Attn:RR  Quote
02-08-2020 02:24 AM  8 days ago
Grimracer

rrKey Veteran

Eau Claire WI

MyPosts All Forum Topic
Good one Cheese Curd.. If I fire that bad boy up i might get another ticket...LOL

205.00 for 15 over in the state of WI.. AND 4 points.. LOL..

New suspension work on YELLOW BLURR this spring.. so.. Daddys going to need to sell street side Curds to make it up!

Grim
Michael J Zaborowski
Futaba USA
AMA 124909
IRCHA 5453
SHARE  PM  EMAIL  GALLERY  Attn:RR  Quote
02-08-2020 03:10 PM  8 days ago
Grimracer

rrKey Veteran

Eau Claire WI

MyPosts All Forum Topic
Tail drive tube...

Should I be able to slide that tube out the back of the machine? Before I attempt to extract it i would like to know what to expect.. Right now.. its not able to be slid fore and aft.

Grim
Michael J Zaborowski
Futaba USA
AMA 124909
IRCHA 5453
SHARE  PM  EMAIL  GALLERY  Attn:RR  Quote
02-08-2020 03:44 PM  8 days ago
Notar

rrKey Veteran

Taxachussetts

MyPosts All Forum Topic
Not normally without work.
The grub screws which hold on the claw coupler up front have marked the tube, so it would not clear the center bearing which should have been installed in the middle of the tail boom. Without using a file to get rid of the grub screw marks, the shaft would not clear this bearing. At best, it still may not clear from the insert placed at the front of the tube, expanding it slightly.
SHARE  PM  EMAIL  GALLERY  Attn:RR  Quote
02-08-2020 04:40 PM  8 days ago
Grimracer

rrKey Veteran

Eau Claire WI

MyPosts All Forum Topic
Thank you.

I am hoping to slip the tube back a few inches to install the cruciform and clip on the tail gearbox output.. and then side it back in.. the TT is stuck in the center bearing.

I might have to cut a access hole in the tailboom near the gearbox housing and I would like to make that a last resort.

Kind Regards

Grim
Michael J Zaborowski
Futaba USA
AMA 124909
IRCHA 5453
SHARE  PM  EMAIL  GALLERY  Attn:RR  Quote
02-09-2020 07:37 PM  7 days ago
Grimracer

rrKey Veteran

Eau Claire WI

MyPosts All Forum Topic
I did cut the access hole.. this worked great.

More to go!

Grim
Michael J Zaborowski
Futaba USA
AMA 124909
IRCHA 5453
SHARE  PM  EMAIL  GALLERY  Attn:RR  Quote
WATCH
 2 pages [ <<    <     1     ( 2 )    >    >> ] 682 views POST REPLY
HomeScale✈️AircraftScale HeliVario Scale Helicopters › Vario 1:6th "Big" Jet Ranger
 Print TOPIC  Make Suggestion 

 7  Topic Subscribe

Monday, February 17 - 2:07 am - Copyright © 2000-2020 RunRyder   EMAILEnable Cookies

Login Here
 New Subscriptions 
 Buddies Online