RunRyder RC
WATCH
 1 page 141 views POST REPLY
Home✈️Aircraft🚁HelicopterHIROBOHirobo Freya › Washer on ssr head
07-21-2019 07:17 PM  34 days ago
Topic Vote0Post 1
Jerman

rrApprentice

Longview, TX

MyPosts All Forum Topic
Washer on ssr head
Guys after pressing bearings inside the arms of an SSR 6 head I’ve noticed maybe a millimeter or less of play on one of the arms between it and the head. Should I use a washer for it or not and if I do should I go ahead and put one on the other side as well, thanks
SHARE  PM  EMAIL  GALLERY  Attn:RR  Quote
07-21-2019 07:19 PM  34 days ago
TMoore

rrMaster

Cookeville, TN

MyPosts All Forum Topic
Picture?Delayed Response Operator Not Engaged
AMA SECTION 336 = Gone, replaced by the FAA
Drones = EVIL
SHARE  PM  EMAIL  HOMEPAGE  GALLERY  Attn:RR  Quote
07-22-2019 02:38 AM  34 days ago
Jerman

rrApprentice

Longview, TX

MyPosts All Forum Topic
No picture needed, just a small amount of side to side movement between the arm and the head, approximately a millimeter or less on one side
SHARE  PM  EMAIL  GALLERY  Attn:RR  Quote
07-22-2019 03:12 AM  34 days ago
jbjones

rrVeteran

Columbus, Mississippi

MyPosts All Forum Topic
Jerman...
No picture needed
I think what Terry is saying, is that a picture would be most helpful in determining what the issue actually is. Terry has a boatload of Hirobo knowledge. Why not give him a chance to see what the problem may be?

Adding parts to make something spec may not produce the outcome you desire. At any rate, hope you get it sorted and flying well.
J. B. Jones
SHARE  PM  EMAIL  HOMEPAGE  GALLERY  Attn:RR  Quote
07-23-2019 03:37 PM  32 days ago
JLF92677

rrApprentice

Southern California

MyPosts All Forum Topic
Jerman, I assume you mean by “arms” blade holders. Did you install the spacer collar in-between the inner and outer bearings?
SHARE  PM  EMAIL  GALLERY  Attn:RR  Quote
07-23-2019 05:55 PM  32 days ago
Jerman

rrApprentice

Longview, TX

MyPosts All Forum Topic
Hello, yes I did. The amount of play is very small, a millimeter or less. Don’t know if the outer thrust bearing has something to do with it or not.
SHARE  PM  EMAIL  GALLERY  Attn:RR  Quote
07-24-2019 02:56 AM  32 days ago
JLF92677

rrApprentice

Southern California

MyPosts All Forum Topic
Try swapping the blade holders to the opposite side spindle and see if the gap is the same on the spindle side that currently has the gap. This will narrow the problem to either the blade grip in question or the spindle.
SHARE  PM  EMAIL  GALLERY  Attn:RR  Quote
07-24-2019 04:43 AM  32 days ago
Jerman

rrApprentice

Longview, TX

MyPosts All Forum Topic
Seems I may have tried that the other day and was still the same but I’ll try it again and see, thanks
SHARE  PM  EMAIL  GALLERY  Attn:RR  Quote
07-24-2019 04:57 AM  32 days ago
TMoore

rrMaster

Cookeville, TN

MyPosts All Forum Topic
Jerman, if you would use the correct terminology on these heads we would be able to help you more efficiently and not have to drag bits and pieces of information out of you in an effort to put the picture together. Blade grips/holders are not arms.

If you get free play in the blade grips after you tighten up the feathering spindle bolts there is definitely something amiss.

On an SSR-6 head there are two feathering spindles, one on each side of the Yoke. If you haven't built the blade grips according to the parts diagram you will have free play in the blade grip assembly.
Delayed Response Operator Not Engaged
AMA SECTION 336 = Gone, replaced by the FAA
Drones = EVIL
SHARE  PM  EMAIL  HOMEPAGE  GALLERY  Attn:RR  Quote
08-03-2019 07:00 AM  22 days ago
Jerman

rrApprentice

Longview, TX

MyPosts All Forum Topic
SHARE  PM  EMAIL  GALLERY  Attn:RR  Quote
WATCH
 1 page 141 views POST REPLY
Home✈️Aircraft🚁HelicopterHIROBOHirobo Freya › Washer on ssr head
 Print TOPIC  Make Suggestion 

 3  Topic Subscribe

Sunday, August 25 - 10:53 am - Copyright © 2000-2019 RunRyder   EMAILEnable Cookies

Login Here
 New Subscriptions 
 Buddies Online