RunRyder RC
rrTV-PHOTO  GALLERIES  MY GALLERY   HELP-FAQ
🚁Helicopter Forum Topic
myHOME PM pmRR MEMBERS 261 ONLINE 2 EVENTS SEARCH REGISTER  START HERE
 4  Topic Subscribe
WATCH
  1 page 462 views Post Reply
Home › RC & Power › ✈️Aircraft › 🚁Helicopter › Flybarless Rotor Head Systems › bavarianDEMON › Power question.
11-16-2018 02:57 AM  27 months ago
Topic Vote0Post 1
Raptor Freak

rrApprentice

Auburn, Wa

MyPosts All Forum Topic
Power question.
Im running a castle pro 20amp bec on the Demon. It shows in the manual only one power input. Is there a way to run both outputs to the unit? Or am i only able to run 1. How would i setup a backup guard? LOGO 700 w/3x and 2 spektrum satellites.
SHARE  PM  EMAIL  GALLERY  Attn:RR  Quote
11-16-2018 12:30 PM  27 months ago
0Post 2
A&J

rrApprentice

Hudson FL 34667

MyPosts All Forum Topic
💎Sustaining Member
Any channel that's open
On the fly bar controller
Do not use a setup portLets do the time warp againnn !
SHARE  PM  EMAIL  Attn:RR  Quote
11-16-2018 09:04 PM  27 months ago
0Post 3
Raptor Freak

rrApprentice

Auburn, Wa

MyPosts All Forum Topic
Ok thanks.
SHARE  PM  EMAIL  GALLERY  Attn:RR  Quote
11-16-2018 09:09 PM  27 months ago
0Post 4
ICUR1-2

rrElite Veteran

Ottawa, Ontario

MyPosts All Forum Topic
You could use y harness to servo inputspending time, paying attention
SHARE  PM  EMAIL  GALLERY  Attn:RR  Quote
11-16-2018 09:52 PM  27 months ago
0Post 5
DemetriusUSN

rrVeteran

Virginia Beach, Va USA

MyPosts All Forum Topic
Using a y harness, I was taught was pointless. You want both power leads plugged into the unit.Minicopter Triabolo 700, Minicopter Diabolo 700, Minicopter Diabolo 600, Minicopter Diabolo 550, Goblin 770, HD 750, HD Cell 500
SHARE  PM  EMAIL  HOMEPAGE  GALLERY  Attn:RR  Quote
11-17-2018 01:47 AM  27 months ago
0Post 6
ICUR1-2

rrElite Veteran

Ottawa, Ontario

MyPosts All Forum Topic
DemetriusUSN Using a y harness, I was taught was pointless. You want both power leads plugged into the unit.
Yes this can be achieved by using a y harness. Please read what you write before posting spending time, paying attention
SHARE  PM  EMAIL  GALLERY  Attn:RR  Quote
11-17-2018 11:02 AM  27 months ago
0Post 7
DemetriusUSN

rrVeteran

Virginia Beach, Va USA

MyPosts All Forum Topic
ICUR1-2 Yes this can be achieved by using a y harness. Please read what you write before posting
Okay, this is one of the main reasons there is so much confusion, but I'll try and explain it a tad gooder for you because obviously you don’t understand because the post is for you. The purpose is to use 2 BEC output leads, which enable up to 10 amp current, as one receiver slot can only take max 5 amp continuous.Minicopter Triabolo 700, Minicopter Diabolo 700, Minicopter Diabolo 600, Minicopter Diabolo 550, Goblin 770, HD 750, HD Cell 500
SHARE  PM  EMAIL  HOMEPAGE  GALLERY  Attn:RR  Quote
11-17-2018 12:57 PM  27 months ago
0Post 8
ICUR1-2

rrElite Veteran

Ottawa, Ontario

MyPosts All Forum Topic
A rx has all of the + sharing the same rail & all - share the same rail. Only signal are separate input
.
You can plug as many BEC input leads as you want with y harness.

I'm starting to see why this sight is dead. Too many people talking BS.spending time, paying attention
SHARE  PM  EMAIL  GALLERY  Attn:RR  Quote
11-17-2018 05:39 PM  27 months ago
0Post 9
Heli Fanatix

rrVeteran

Fountain Valley, CA

MyPosts All Forum Topic
On the HC3-SX / BD3-SX there an port for a fourth servo
- if the FBL unit is oriented with port on left & LED on right
- last port on bottom
- this port is left open if you are using a Logo 700

As explained, all the positives are common aswell as negatives.

This will resolve your situation.
SHARE  PM  EMAIL  GALLERY  Attn:RR  Quote
11-17-2018 06:42 PM  27 months ago
0Post 10
A&J

rrApprentice

Hudson FL 34667

MyPosts All Forum Topic
💎Sustaining Member

Watch at YouTube

Lets do the time warp againnn !
SHARE  PM  EMAIL  Attn:RR  Quote
11-17-2018 06:49 PM  27 months ago
0Post 11
A&J

rrApprentice

Hudson FL 34667

MyPosts All Forum Topic
💎Sustaining Member

Watch at YouTube

Lets do the time warp againnn !
SHARE  PM  EMAIL  Attn:RR  Quote
11-17-2018 06:52 PM  27 months ago
0Post 12
A&J

rrApprentice

Hudson FL 34667

MyPosts All Forum Topic
💎Sustaining Member
https://www.bavariandemon.com/filea...al-X-series.pdfLets do the time warp againnn !
SHARE  PM  EMAIL  Attn:RR  Quote
11-18-2018 04:55 AM  27 months ago
0Post 13
rcflyerheli

rrKey Veteran

Granbury, TX USA

MyPosts All Forum Topic
It sounds to me you guys are talking apples and oranges. Plugging both BEC leads into a Y harness and plugging the wire harness into one servo slot really does nothing. You still have the 5a bottleneck.

However, plugging one BEC lead into a servo slot and then plugging the Y harness into another servo slot with the other BEC lead into one leg and the servo into the other leg gets your 10a to the FBL and also gets power to the servo.Logo 700, Specter 700, Goblin 700, Trex 700DFC, Gaui X7, Logo 690SX, Logo 600SX; Trex 470 Trex 500
Amain Team Rep
SHARE  PM  EMAIL  GALLERY  Attn:RR  Quote
WATCH
  1 page 462 views Post Reply
Home › RC & Power › ✈️Aircraft › 🚁Helicopter › Flybarless Rotor Head Systems › bavarianDEMON › Power question.
Print TOPIC

 4  Topic Subscribe

Thursday, February 25 - 1:09 pm - Copyright © 2000-2021 RunRyder   EMAIL • Enable Cookies

Login Here
 New Subscriptions 
 Buddies Online