RunRyder RC
WATCH
 1 page 193 views POST REPLY
Home✈️Aircraft🚁Helicoptere-BladeBlade 450 › 330X AR636A in 450X
06-22-2018 03:55 AM  15 months ago
Topic Vote0Post 1
Joe Jet

rrNovice

CA & Japan

MyPosts All Forum Topic
330X AR636A in 450X
Has anyone tried this? It seems like it should be an easy drop in as the mechanics are the same. I ordered a 330X receiver BLH4002 and stuck it on a 450X. The forward servo is reversed as well as the cyclic gyro function. Can’t figure it out.
SHARE  PM  EMAIL  Attn:RR  Quote
06-22-2018 06:07 PM  15 months ago
Joe Jet

rrNovice

CA & Japan

MyPosts All Forum Topic
Figured out the servo connections and reversing etc. Had to switch the Ail, L cyc, and aux 1, R cyc, servos. that straightened everything all out. Using the stock 330X TX setup from spektrum and just modified the Throttle and Pitch curves to the stock 450X settings. Everything bench tests well, but when I power up the swash goes nuts as if the gyro gains are too high. I tried turning the P, I, and D gains down, but no improvement. Any ideas?
SHARE  PM  EMAIL  Attn:RR  Quote
06-23-2018 09:49 PM  14 months ago
Joe Jet

rrNovice

CA & Japan

MyPosts All Forum Topic
Removed the main blades to eliminate a main rotor vibration issue, but swash still goes spastic when spinning up. Going to remove tail blades next. If that doesnt work ill try remounting receiver with thinner tape. I used soft 3mm thick Futana tape.
SHARE  PM  EMAIL  Attn:RR  Quote
07-04-2018 07:20 AM  14 months ago
Joe Jet

rrNovice

CA & Japan

MyPosts All Forum Topic
remounted the 636 and was able to fly it into a hover. still some vibration in the tail though. going to check belt tension and replace the tail blades next. At least I have it flying now.
SHARE  PM  EMAIL  Attn:RR  Quote
07-16-2018 04:02 AM  14 months ago
Joe Jet

rrNovice

CA & Japan

MyPosts All Forum Topic
Still waiting to get back to states to get new tail blades. Been messing with it while 8n Japan. dialed the cyclic gains down from default 100 to 90. Flys a little better. Going to try cyclic p gain at 80 next and test fly. Really need to get fresh tail blades though.
SHARE  PM  EMAIL  Attn:RR  Quote
10-13-2018 07:37 PM  11 months ago
Joe Jet

rrNovice

CA & Japan

MyPosts All Forum Topic
Never got the 636 to work perfect in the 450X. AR7200/7210 set up is so much easier and flies much better anyway. Started doing some light acro with my 230S with 636 and although the 230 is super stable with the 636 in sport flight it is very inaccurate while doing acro. The 450X loops and rolls with beautiful precision. So, what I have learned from this experiment is dutch the 636 and stick to AR7200/7210; well worth the added expense.
SHARE  PM  EMAIL  Attn:RR  Quote
WATCH
 1 page 193 views POST REPLY
Home✈️Aircraft🚁Helicoptere-BladeBlade 450 › 330X AR636A in 450X
 Print TOPIC  Make Suggestion 

 1  Topic Subscribe

Monday, September 16 - 2:00 am - Copyright © 2000-2019 RunRyder   EMAILEnable Cookies

Login Here
 New Subscriptions 
 Buddies Online