WATCH |
1 page 1042 views |
Post Reply |
05-17-2018 03:11 AM 35 months ago
joshmoha
rrApprentice midland texas |
Setup menu j Setting up my trex 600 I went to step j level heli set pitch gauge level. Went to 6 deg. Positive no blue light till around 8 deg.went back the other way to 6 deg neg. blue light seems in to have a wider range in neg. will this be ok.not sure what 6 deg. And the blue light have to do with each other. |
SHARE PM EMAIL GALLERY Attn:RR Quote |
05-17-2018 04:05 AM 35 months ago
pH7
rrKey Veteran Sterling Heights, MI - USA |
The purpose of step J is to teach the BeastX where 6 degrees is in your heli's geometry. The purpose is NOT to get a blue light. If you don't have a blue light at 6 degrees it just means that you may want to try different size control arms on your cyclic servos to get better resolution.Phil Heavin |
SHARE PM EMAIL GALLERY Attn:RR Quote |
05-17-2018 02:05 PM 35 months ago
joshmoha
rrApprentice midland texas |
so should I go back and set it to 6 deg pos. thanks |
SHARE PM EMAIL GALLERY Attn:RR Quote |
05-17-2018 02:33 PM 35 months ago
Heli_Splatter
rrElite Veteran USA |
You should seek help from someone who knows what they are doing before you hurt yourself. |
SHARE PM EMAIL GALLERY Attn:RR Quote |
05-17-2018 11:49 PM 35 months ago
joshmoha
rrApprentice midland texas |
Have not hurt anyone in thr 4 years I have been flying. I thought this site was to get help my other flybarless just said to set to the deg. There are no lights. I did get my answer from this site. |
SHARE PM EMAIL GALLERY Attn:RR Quote |
05-17-2018 11:57 PM 35 months ago
JuanRodriguez
rrProfessor The Villages, Florida 💎Sustaining Member |
I think you got your answer back in post 2 ....Been there, done that and old enough to know better..... |
SHARE PM EMAIL GALLERY Attn:RR Quote |
05-18-2018 01:50 AM 35 months ago
05-23-2018 11:45 AM 35 months ago
Richardmid1
rrProfessor Leeds, England |
What Phil said in the first reply is correct.I think I have always used right aileron with the heli facing me which would be negative blade pitch. I think if you are getting different light colours at the 6 degrees it would suggest that your servos aren't at 90 degrees at zero pitch or that you used too much adjustment in step G to get them to 90 degrees and need to choose servo arms closer to 90 degrees with the sub trim adjustments reset.60% of the time, it works every time! |
SHARE PM EMAIL HOMEPAGE GALLERY Attn:RR Quote |
06-18-2018 08:49 PM 34 months ago
Ken Filloon
rrVeteran Highland, Michigan |
Which head and swash do you have? You can move in a hole on some swash plates to increase the resolution. |
SHARE PM EMAIL GALLERY Attn:RR Quote |
09-04-2018 06:37 PM 32 months ago
# 1 VIBE USA
rrApprentice North East,VT |
I have a new Align 700 nitro with the BeastX when I try to take off the helicopter wants to put the tail rotor in the ground is this normal ?can u make it go faster |
SHARE PM EMAIL GALLERY Attn:RR Quote |
09-05-2018 11:09 AM 32 months ago
Richardmid1
rrProfessor Leeds, England |
# 1 VIBE USA I have a new Align 700 nitro with the BeastX when I try to take off the helicopter wants to put the tail rotor in the ground is this normal ? Do you mean it wants to pitch back towards you?How is the C of G?Is the swash level?Are the cyclic gyro directions and control input directions correct? (setup steps I and M).60% of the time, it works every time! |
SHARE PM EMAIL HOMEPAGE GALLERY Attn:RR Quote |
09-07-2018 04:36 PM 31 months ago
11-03-2018 07:55 PM 30 months ago
# 1 VIBE USA
rrApprentice North East,VT |
reset l and M and it is all good now I bought the usb2sys and BLE2SYS do these need the computer be fore using or they program already 4.1.5 ?can u make it go faster |
SHARE PM EMAIL GALLERY Attn:RR Quote |
WATCH |
1 page 1042 views |
Post Reply |
5 Topic Subscribe
Thursday, April 22 - 7:14 pm - Copyright © 2000-2021 RunRyder EMAIL • Enable Cookies