RunRyder RC
WATCH
 1 page 477 views POST REPLY
HomeAircraftHelicopterEngines Plugs Mufflers Fuel › Try to overhaul.
04-23-2018 02:19 AM  3 months agoPost 1
Dirtpen

rrNovice

Illinois

My Posts: All  Forum  Topic

We will a see if parts get delivered. Going to get her pop in again

Rubbed out the crank case to shinny.

PM  EMAIL  GALLERY  Attn:RR  Quote
04-23-2018 11:04 PM  3 months agoPost 2
Dirtpen

rrNovice

Illinois

My Posts: All  Forum  Topic

Parts showed up.

PM  EMAIL  GALLERY  Attn:RR  Quote
04-24-2018 11:53 PM  3 months agoPost 3
Dirtpen

rrNovice

Illinois

My Posts: All  Forum  Topic

No way any engine parts going into the wife new oven, so I used a body shop heat gun. Looks like a hair drier ,heated the block about hot so just beyond picking up with bare hands and the rear bearing went in all the way very easy.then holding down on the bearing to its seat, I used shop air to cool the parts. Drop the crank in and pushed hard with my fingers on the front brng. front seats home easy no heat.ill do some more tomarrow I'm done, building big blocks takes its role on the body ya know. Forgot a pic I'll get one up .

PM  EMAIL  GALLERY  Attn:RR  Quote
04-25-2018 12:31 AM  3 months agoPost 4
spaceman spiff

rrKey Veteran

Tucson

My Posts: All  Forum  Topic

Nice little project.

PM  EMAIL  GALLERY  Attn:RR  Quote
04-27-2018 12:15 AM  3 months agoPost 5
Dirtpen

rrNovice

Illinois

My Posts: All  Forum  Topic

Looking at the nitromethane barrel valves. This is high performance stuff here bud.if you run one of these engines and set it up for any amounts of time, rust will happen garonteed. Rust in the bearings is easy to prevent by removing back plate and oil,but this. This is where the action is. Dentist tools, gun swabs.this one looks good for me ,the mid long needle nasty.

PM  EMAIL  GALLERY  Attn:RR  Quote
04-27-2018 12:19 AM  3 months agoPost 6
JuanRodriguez

rrProfessor

The Villages, Florida

My Posts: All  Forum  Topic

You're smoking some good weed, aren't you ??

Been there, done that and old enough to know better.....

PM  EMAIL  GALLERY  Attn:RR  Quote
04-27-2018 12:24 AM  3 months agoPost 7
Dirtpen

rrNovice

Illinois

My Posts: All  Forum  Topic

I cleaned the damn thing up after the picture , dang. Only the best on the planet. Hey when she runs again I'm making a video just for you

PM  EMAIL  GALLERY  Attn:RR  Quote
04-27-2018 12:51 AM  3 months agoPost 8
JuanRodriguez

rrProfessor

The Villages, Florida

My Posts: All  Forum  Topic

Dirtpen
I cleaned the damn thing up after the picture , dang. Only the best on the planet. Hey when she runs again I'm making a video just for you
You mean, BEFORE the pic ??? Please do post a video........

I've had several YS motors and they are the best ! Well, Saito motors are pretty good too !

Been there, done that and old enough to know better.....

PM  EMAIL  GALLERY  Attn:RR  Quote
05-01-2018 01:19 AM  3 months agoPost 9
Dirtpen

rrNovice

Illinois

My Posts: All  Forum  Topic

Polished out unit. Check . Piston ,check, . . Go ahead ,is this where you want to be when jeasus comes back picking on dirt pen?

PM  EMAIL  GALLERY  Attn:RR  Quote
WATCH
 1 page 477 views POST REPLY
HomeAircraftHelicopterEngines Plugs Mufflers Fuel › Try to overhaul.
 Print TOPIC  Make Suggestion 

 2  Topic Subscribe

Friday, August 17 - 6:22 am - Copyright © 2000-2018 RunRyder   EMAILEnable Cookies

Login Here
 New Subscriptions 
 Buddies Online