RunRyder RC
WATCH
 1 page 303 views POST REPLY
HomeAircraftHelicopterRadio - Futaba FASST › Futaba T10CG elevator function gone in idle up two.
04-22-2018 08:43 AM  89 days agoPost 1
wpoel

rrNovice

NETHERLANDS

My Posts: All  Forum  Topic

Above problem with my radio and in servo test position nothing moves in idle up two.Condition switch same as other heli’s.
Very very strange problem and I have it in two heli programs.
Maybe reset the program of the heli??

Somebody idees???

PM  EMAIL  Attn:RR  Quote
04-23-2018 05:18 AM  88 days agoPost 2
Dr.Ben

rrMaster

Richmond, VA, USA

My Posts: All  Forum  Topic

Are you saying this only happens in servo test mode or when the transmitter is simply in idle 2? One funtion or all? Your description is conflicting.

Ben Minor

Peak Aircraft/Team Minicopter Team Futaba Team Kontronik USA

PM  EMAIL  GALLERY  Attn:RR  Quote
04-23-2018 05:45 AM  88 days agoPost 3
wpoel

rrNovice

NETHERLANDS

My Posts: All  Forum  Topic

Yes you are right but only elevator is not working in idle up two.I use also servo test position tot check.
No problems with my other models.

PM  EMAIL  Attn:RR  Quote
04-23-2018 01:13 PM  88 days agoPost 4
BeltFedBrowning

rrKey Veteran

Kansas City

My Posts: All  Forum  Topic

Did you accidentally enable a mix for that mode?

PM  EMAIL  GALLERY  Attn:RR  Quote
04-23-2018 04:56 PM  88 days agoPost 5
wpoel

rrNovice

NETHERLANDS

My Posts: All  Forum  Topic

No mix and I checked so many things.
I am thinking to copy other model to this model position but probably the problem
will be the same and maybe it is even a software problem...

PM  EMAIL  Attn:RR  Quote
04-23-2018 05:38 PM  88 days agoPost 6
Dr.Ben

rrMaster

Richmond, VA, USA

My Posts: All  Forum  Topic

See what it does on another model already programmed. Just
to check if the servos act right.

Ben Minor

Peak Aircraft/Team Minicopter Team Futaba Team Kontronik USA

PM  EMAIL  GALLERY  Attn:RR  Quote
04-24-2018 01:46 AM  87 days agoPost 7
Rojoalfa

rrVeteran

Punta de Mata, Monagas-Venezuela

My Posts: All  Forum  Topic

/
/
Very strange fail.
Just for review... Check swash function, atv function then dual rate while operating the idle switch.
You have corrupted memory.

Either way, reset the memory model and reprogram the whole helicopter.

Don't look back.
It is better to start over a clean memory than from a crash...

/

Saludos cordiales,

PM  EMAIL  HOMEPAGE  GALLERY  Attn:RR  Quote
04-24-2018 07:38 AM  87 days agoPost 8
wpoel

rrNovice

NETHERLANDS

My Posts: All  Forum  Topic

I will check all your sugestions and let you know later on.
On three models everything works fine.
The two models with failing elevator had fail safe set up problems on throttle (e heli’s)by the way.
So I will have a closer look at that point as well!

PM  EMAIL  Attn:RR  Quote
04-24-2018 08:29 PM  86 days agoPost 9
wpoel

rrNovice

NETHERLANDS

My Posts: All  Forum  Topic

I checked some more things but no result.
I wrote down all settings and finally I copied a proper working model to the failing model number.
Problem solved now so probably software related in transmitter.
This topic can be closed.
Thanks everybody.

PM  EMAIL  Attn:RR  Quote
WATCH
 1 page 303 views POST REPLY
HomeAircraftHelicopterRadio - Futaba FASST › Futaba T10CG elevator function gone in idle up two.
 Print TOPIC  Make Suggestion 

 1  Topic Subscribe

Friday, July 20 - 7:49 pm - Copyright © 2000-2018 RunRyder   EMAILEnable Cookies

Login Here
 New Subscriptions 
 Buddies Online