RunRyder RC
WATCH
 1 page 866 views Post Reply
01-23-2018 01:13 AM  3 years ago
Topic Vote0Post 1
nappyroots2182

rrElite Veteran

Moline, il

MyPosts All Forum Topic
Non heading hold
I found 2 places in the software that say heading hold with its boxed check marked. But I cant seem to get it to uncheck so I can do a mechanical trim flight on the tail
SHARE  PM  EMAIL  GALLERY  Attn:RR  Quote
01-23-2018 01:26 AM  3 years ago
ICUR1-2

rrElite Veteran

Ottawa, Ontario

MyPosts All Forum Topic
You lower the gyro gain to get into rate mode. It goes into HH when the unit sees over 45%spending time, paying attention
SHARE  PM  EMAIL  GALLERY  Attn:RR  Quote
01-23-2018 01:39 AM  3 years ago
nappyroots2182

rrElite Veteran

Moline, il

MyPosts All Forum Topic
Ok ill give it a try tomorrow. Just figured I could of unchecked the box but doesn't look that way
SHARE  PM  EMAIL  GALLERY  Attn:RR  Quote
01-23-2018 12:21 PM  3 years ago
nappyroots2182

rrElite Veteran

Moline, il

MyPosts All Forum Topic
Played with it this morning. I was given the heli and the program off a sd card so it was setup different then I'm used to. He was using the gyro screen and had a 3 position switch at 40,40,50. I change it to 40,40,-40. Usually I use gear channel and not the gyro screen. Now only if the weather would clear up
SHARE  PM  EMAIL  GALLERY  Attn:RR  Quote
01-23-2018 12:57 PM  3 years ago
ICUR1-2

rrElite Veteran

Ottawa, Ontario

MyPosts All Forum Topic
I hear ya, I have the itch.

45% in the radio may not be 45% in the unit. Use the software to check the variance between the unit and radio.
spending time, paying attention
SHARE  PM  EMAIL  GALLERY  Attn:RR  Quote
01-24-2018 02:27 AM  3 years ago
pctomlin

rrVeteran

Texas

MyPosts All Forum Topic
Positive numbers are HH and the inverse is the same value in rate mode.
SHARE  PM  EMAIL  GALLERY  Attn:RR  Quote
01-26-2018 10:20 AM  3 years ago
rik

rrNovice

Italy

MyPosts All Forum Topic
ICUR1-2 45% in the radio may not be 45% in the unit. Use the software to check the variance between the unit and radio.
You can have the same value in the transmitter and Brain by correcting the endpoints/ATV of the transmitter as you should in panel 5 of the wizard for all channels. Not only for aileron, elevator, throttle, tail, but also for tail gain and aux channels.
SHARE  PM  EMAIL  HOMEPAGE  GALLERY  Attn:RR  Quote
01-26-2018 12:48 PM  3 years ago
nappyroots2182

rrElite Veteran

Moline, il

MyPosts All Forum Topic
Thanks rik,I just checked and changed that. Also found that my flight mode agilitys were not in my stunt mode switch. I guess that's what I get for copying from sd card that someone else gave me. Lol. It was flying really well last nite

SHARE  PM  EMAIL  GALLERY  Attn:RR  Quote
WATCH
 1 page 866 views Post Reply
Print TOPIC

 3  Topic Subscribe

Tuesday, October 26 - 7:01 pm - Copyright © 2000-2021 RunRyder   EMAILEnable Cookies

Login Here
 New Subscriptions 
 Buddies Online