RunRyder RC
WATCH
 1 page 816 views POST REPLY
Home✈️Aircraft🚁HelicopterHelicopter Main Discussion › Question on align 470 setup- spektrum
07-07-2017 01:30 AM  33 months ago
Topic Vote0Post 1
Aswick3

rrNovice

Ct 06710

MyPosts All Forum Topic
Question on align 470 setup- spektrum
I have an ar7110 rx I bought for a century model and am not currently using.
The combo kit for the 470L kit requires 7 channel rx (as we all know). Can I use that rx with the beast x that comes with the kit? The rx has a power lead but I'm thinking I wouldn't need to use the power lead and can clip them off?

If I can't use that rx, what rx are you guys using on those particular models?
I have 3 helis now that I'm using the ar7200bx and I do like that rx, I guess I can prolly go that route as well but I wanted to use the beast x that came with it.
Thanks!
SHARE  PM  EMAIL  GALLERY  Attn:RR  Quote
07-07-2017 05:02 AM  33 months ago
dkshema

rrMaster

Cedar Rapids, IA

MyPosts All Forum Topic
The combo kit for the 470L kit requires 7 channel rx (as we all know).
1. throttle
2. Pitch (elevator)
3. Roll (aileron)
4. Yaw (rudder)
5. Rudder gain
6. Collective pitch

What is number 7?
-----
Dave

* Making the World Better -- One Helicopter at a time! *

Team Heliproz
SHARE  PM  EMAIL  GALLERY  Attn:RR  Quote
07-07-2017 11:39 AM  33 months ago
Aswick3

rrNovice

Ct 06710

MyPosts All Forum Topic
Throttle
Ail
Ele
Gear
Aux 1
•thr
•Gear
•Rudder
•Aux 2

The 4 with the 'bullets' are regulated at 5.2v, other channels are not
SHARE  PM  EMAIL  GALLERY  Attn:RR  Quote
07-07-2017 01:26 PM  33 months ago
Danny Calderone

rrKey Veteran

South Jersey

MyPosts All Forum Topic
💎Sustaining Member
I would say you can use it with no issue at all.Signature
SHARE  PM  EMAIL  GALLERY  Attn:RR  Quote
07-07-2017 01:31 PM  33 months ago
Aswick3

rrNovice

Ct 06710

MyPosts All Forum Topic
Ok great, thanks.
I don't need the power leads I believe and can eliminate that no?
SHARE  PM  EMAIL  GALLERY  Attn:RR  Quote
07-07-2017 04:30 PM  33 months ago
dkshema

rrMaster

Cedar Rapids, IA

MyPosts All Forum Topic
I did some follow-up investigation and found a 470L manual. It does need a 7 channel minimum TX/RX if you use the electronics supplied in the kit.

You may want to ask Spektrum about using the AR7110 without using the standard battery input leads, however. That may not be kosher.

Mea Culpa. Mea Maximus Culpa.
-----
Dave

* Making the World Better -- One Helicopter at a time! *

Team Heliproz
SHARE  PM  EMAIL  GALLERY  Attn:RR  Quote
07-07-2017 05:20 PM  33 months ago
Heli_Splatter

rrElite Veteran

USA

MyPosts All Forum Topic
Governor??
SHARE  PM  EMAIL  GALLERY  Attn:RR  Quote
07-07-2017 07:06 PM  33 months ago
Danny Calderone

rrKey Veteran

South Jersey

MyPosts All Forum Topic
💎Sustaining Member
I've never done it, but I know a few guys that have run them via the ESC voltage supply and left the large leads unplugged or clipped them off ...for whatever reason.Signature
SHARE  PM  EMAIL  GALLERY  Attn:RR  Quote
07-07-2017 10:26 PM  33 months ago
Heli_Splatter

rrElite Veteran

USA

MyPosts All Forum Topic
I don't think that I would cut the battery leads off (just me). It is yours, do what ever.

I am using Spektrum receivers with my beastX FBL units. No reason this will not work with yours.

I am switching over to a 7 channel single line input Spektrum Receiver because I want the governor functions available on my BeastX Plus HD unit. I thought changing to that receiver was the least work and best result. You will see in the BeastX documentation (if yours has governor) that you cannot use a standard receiver for the governor function.
SHARE  PM  EMAIL  GALLERY  Attn:RR  Quote
07-08-2017 12:04 AM  33 months ago
Aswick3

rrNovice

Ct 06710

MyPosts All Forum Topic
Thanks again guys. I normally don't use that type of rx but I have it so I figured if I can use it I'll at least give it a try anyways. But well see.
Appreciate the feedback
SHARE  PM  EMAIL  GALLERY  Attn:RR  Quote
07-08-2017 07:07 PM  33 months ago
ticedoff8

rrKey Veteran

Morgan Hill, CA. USA

MyPosts All Forum Topic
Use a volt/ohm meter to measure the resistance from the + battery lead to one of the non-regulated servo power pins.

Since the 5.2v regulated channels are throttle, gear, rudder and aux 2, measure the resistance on aileron, elevator, aux 1 (swash servos)

If you get 0 ohms, then I would say you can cut off the battery leads and power the AR7110 from one of the swash servo power pins.

You cannot power the AR7110 externally through one of the regulated channel's servo connector.
If the regulator has protection, it will not power up.
If the regulator has no protection, it will most likely smoke the regulator

HOWEVER...
According to the wiring diagram for the BeastX, connections from a "traditional" receiver (like the AR7110) require connecting several M-to-M cables from the receiver's servo ports to the BeastX first.

And that looks like it is going to mix some regulated channels (rudder, gear and aux 2) with unregulated channels (3 swash)

I would bet this will smoke the AR7110.

I would use the Spektrum DSMX satellites.
That will make a lighter and neater installation.
+ > ÷
Believe 1/2 of what you see and none of what you hear.
Fake News will be the downfall of our Republic!
SHARE  PM  EMAIL  GALLERY  Attn:RR  Quote
WATCH
 1 page 816 views POST REPLY
Home✈️Aircraft🚁HelicopterHelicopter Main Discussion › Question on align 470 setup- spektrum
 Print TOPIC  Make Suggestion 

 4  Topic Subscribe

Friday, April 10 - 1:01 am - Copyright © 2000-2020 RunRyder   EMAILEnable Cookies

Login Here
 New Subscriptions 
 Buddies Online