RunRyder RC
 0  Topic Subscribe
WATCH
 1 page 90 views POST REPLY
HomeClassifiedAircraftHelicopter
e-
Classifieds - Battery & Charger
Charger Sold  Powerlab 6 charger and Meanwell 1000 watt supply
06-13-2017 03:25 PM  12 months agoPost 1
RappyTappy

rrProfessor

Traveling the USA

My Posts: All  Forum  Topic

My Classified Activity
My Classified Feedback
Add Classified Feedback

Selling my lightly used charging equipment. Has less than 100 charges run through them, always been used as a pair. All in very good condition, plastic wrap still on charger only a small ding on screen, still under factory warranties.

$200 plus actual shipping cost.

Case extra for $15.

CHARGER SPECS:
For Battery types: Lithium Polymer (1s to 6s balanced, 1s to 2s unbalanced), Lithium Ion (1s to 6s balanced, 1s to 2s unbalanced), Lithium Manganese (1s to 6s balanced, 1s to 2s unbalanced), A123 (LiFePO4) (1s to 6s balanced, 1s to 8s unbalanced), NiCd (1s to 19s), NiMH (1s to 19s), 6v, 12v, 24v Lead Acid batteries (Flooded, Gel, AGM, SLA)
Pack capacity: 20 mAh to 360Ah
Input voltage: 10-32VDC, reverse polarity protected
Input current: 1A to 40A, software limited
Power conversion: Synchronous DC/DC converter, supports multiple switcher frequencies of 31.25 kHz, 62.5 kHz, 125 kHz; user selectable by preset, 85% to 93% efficiency depending on output current
Output battery charge current: Adjustable range 10mA to 40A, limited by 40A input current*
Output battery discharge current: Internal discharge 10mA to 8A, 50W max Regenerative discharge 10mA to 40A, 1000W max**
Continuous max output power: 408W @ +12VDC input, 1000W @ +30VDC
Cell balancing: Resolution 78uV (16 bit) for 1s-8s Li or A123 (LiFePO4) balanced charging
Voltage calibration: Cell voltage measurements are factory calibrated to a standard traceable to NIST; calibration is to +/- 6 mV
Current calibration: Charge current is factory calibrated on a 4A standard; calibration is to +/- 1mA
Measurement accuracy:
Voltage resolution: 78uV (16 bit)
Voltage tolerance: +/- 6mV
Charge current: +/- 1%
Capacity added to pack: +/- 1%
Percent capacity (“Fuel”): +/- 5% (with accurate fuel table defined for battery being charged)
Serial data output: 19.2kbps, 8 bits, 1 start bit, 1 stop bit, no parity
Data integrity: Checksum, CRC checking
Cooling fans: Single, 13 CFM, 50mm diameter
Heat sink: Internal 120W aluminum, thin finned
Output battery connector: “Cellpro” compatible, JST PA series, 9 position
LCD: 2 line, 16 character, light grey/blue backlit
Size: 5.70x5.57x3.40"
Power Supply Specs:
Output Power (110 VAC) 1000W
Output Power (220 VAC) 1000W
Output Voltage 24V DC (adjustable +/-10%)
Output Current 41.7A
Input Voltage 90-132V/180-264V AC (selected by jumper)
Dimensions 278x127x64mm
Weight 2500g
Warranty 2 years
AC Cable Optional


PM  EMAIL  GALLERY  Attn:RR  Quote
WATCH
 1 page 90 views POST REPLY
HomeClassifiedAircraftHelicopter
e-
Classifieds - Battery & Charger
Charger Sold  Powerlab 6 charger and Meanwell 1000 watt supply
 Print TOPIC  Make Suggestion 

 0  Topic Subscribe

Classifieds › HELP-FAQ
Attention Buyers! To receive feedback Post Reply in the seller’s topic. The seller can then click your post's Add Classified Feedback link.
Attention Sellers! Stating price is not mandatory but recommended. Post Reply commentary that interferes with the selling process (and not replied to) will be removed upon request. Click Attn:RR on the offending classified post. Repeated NIB-NIP sales are not allowed. Take it to EBay.
Buyer Beware! RunRyder cannot vouch for any seller's or buyer's credibility and will not accept responsibility for any transactions resulting from the use of this site.

Sunday, June 24 - 3:42 pm - Copyright © 2000-2018 RunRyder   EMAILEnable Cookies

Login Here
 New Subscriptions 
 Buddies Online