RunRyder RC
WATCH
 1 page 1271 views POST REPLY
HomeRC & PowerAircraftHelicopterRadio - Spektrum DSM › Dx9 w Neo set up
12-18-2015 01:56 PM  36 months agoPost 1
blucido

rrApprentice

Plano,Texas

My Posts: All  Forum  Topic

Anybody set up a Dx9 w Neo using Castle Esc as gov, need your suggested settings having problems with assigning channels,for motor ,gov etc.

PM  EMAIL  GALLERY  Attn:RR  Quote
12-18-2015 02:19 PM  36 months agoPost 2
Blackhawk6

rrVeteran

Trenton, Mi

My Posts: All  Forum  Topic

This may help...

http://www.vstabi.info/en/node/1990

Team XpertUSA

PM  EMAIL  GALLERY  Attn:RR  Quote
12-18-2015 05:45 PM  36 months agoPost 3
blucido

rrApprentice

Plano,Texas

My Posts: All  Forum  Topic

ya tried to follow this but DX9 a little different

PM  EMAIL  GALLERY  Attn:RR  Quote
12-18-2015 06:59 PM  36 months agoPost 4
Blackhawk6

rrVeteran

Trenton, Mi

My Posts: All  Forum  Topic

Ok. What are you having trouble with?

Team XpertUSA

PM  EMAIL  GALLERY  Attn:RR  Quote
12-19-2015 12:08 AM  36 months agoPost 5
vburge

rrApprentice

Alabaster, Alabama - US

My Posts: All  Forum  Topic

I helped a buddy setup his DX18, but I don't remember the specifics. You will be using the DX9 0%, 50%, 100% throttle curves and set your Castle governor percentages in the vstabi software. Message me if you want me to try and help over the phone.

Synergy 516
Graupner
Xnova

PM  EMAIL  Attn:RR  Quote
12-21-2015 12:01 AM  36 months agoPost 6
blucido

rrApprentice

Plano,Texas

My Posts: All  Forum  Topic

Two things still having trouble with, 1st thing seems like the tail Gyro compensation is going in wrong direction from within Neo, stick direction is ok, second thing is can't seem to get Castle throttle end points to calibrate properly. The Neo completes it's beeps as if it were ready ,not the pause you look for before you role up to your end points and it then beeps..Thoughts? All other functions seem ok at this time

PM  EMAIL  GALLERY  Attn:RR  Quote
12-21-2015 05:22 AM  36 months agoPost 7
vburge

rrApprentice

Alabaster, Alabama - US

My Posts: All  Forum  Topic

Make sure you have the sensor mounting direction right on the sensor setup tab. On the Transm tab, is the rudder moving in the right direction with your stick movements?
For the throttle end points, the only way I have successfully set endpoints is by powering the vbar separate from the ESC. If that is a problem, you can power up everything normally in hold and decrease the "motor off" value (throttle by collective off) until the motor arms and leave it there. Make sure you have the blades off or motor disengaged from the gear before doing this.

Synergy 516
Graupner
Xnova

PM  EMAIL  Attn:RR  Quote
12-21-2015 02:32 PM  36 months agoPost 8
blucido

rrApprentice

Plano,Texas

My Posts: All  Forum  Topic

One thing I've noticed is when I initialize the vbar system and it goes green the little USB symbol does not turn green ,the "connected" and "ready" symbols do? what does this mean? could it keep it from doing proper set up, and by the way I did check my sensor position and its right, I'm setting up a goblin 570 and it faces forward with the Neo lable up? I even tried doing another set up as some other forums have suggested?

PM  EMAIL  GALLERY  Attn:RR  Quote
12-22-2015 04:03 PM  36 months agoPost 9
blucido

rrApprentice

Plano,Texas

My Posts: All  Forum  Topic

Problems solved, spent time with Ron from Mikado tech support via Teamview , had some switches set up wrong mostly , should be good now, great guy to work with , highly recommend if your having trouble.

PM  EMAIL  GALLERY  Attn:RR  Quote
12-22-2015 08:16 PM  36 months agoPost 10
vburge

rrApprentice

Alabaster, Alabama - US

My Posts: All  Forum  Topic

Glad you got it sorted out. Every person I have interacted with from Mikado has be very helpful.

Synergy 516
Graupner
Xnova

PM  EMAIL  Attn:RR  Quote
WATCH
 1 page 1271 views POST REPLY
HomeRC & PowerAircraftHelicopterRadio - Spektrum DSM › Dx9 w Neo set up
 Print TOPIC  Make Suggestion 

 2  Topic Subscribe

Monday, December 10 - 1:44 am - Copyright © 2000-2018 RunRyder   EMAILEnable Cookies

The RC discussion world needs to consolidate. RR is now one choice for that. Its software is cutting edge. It hosts on-topic advertising. Help RR increase traffic buy making suggestions, posting in RR's new areas (sites) and by spreading the word.

The RunRyder Difference

• Category system to allow Rep/Vendor postings.
• Classifieds with sold (hidden) category.
• Classifieds with separate view new.
• Answer PMs offsite via email reply.
• Member gallery photos with advanced scripting.
• Gallery photo viewer integrated into postings.
• Highly refined search with advanced back end.
• Hosts its own high end fast response servers.
• Hosts thousands of HD event coverage videos.
• Rewrote entire code base with latest technology.
• No off-topic (annoying) click bait advertising.
Login Here
 New Subscriptions 
 Buddies Online