RunRyder RC
WATCH
 2 pages [ <<    <     1     ( 2 )    >    >> ] 5326 views POST REPLY
HomeRC & Power✈️Aircraft🚁HelicopterRadio - Futaba FASST › New firmware for 14sg version 6.0
12-27-2015 05:22 PM  3 years ago
fastrc1

rrKey Veteran

Planet Brooklyn, NY-USA

MyPosts All Forum Topic
Uhh ohhh. What's in V6?RIP Roman Pirozek Jr.
Team Futaba USA
Team Kontronik USA
http://flysrw.com
SHARE  PM  EMAIL  HOMEPAGE  GALLERY  Attn:RR  Quote
12-31-2015 03:47 PM  3 years ago
Romak

rrApprentice

Scotland

MyPosts All Forum Topic
I just went and updated my 14sg to 6.0 but after the completed message I turned it off and on and nothing.

Totally dead. Something has failed.
Hope you get ot fixed Andy. Please let us know!

Thanks
Rod
14sg....... ;-)
SHARE  PM  EMAIL  HOMEPAGE  GALLERY  Attn:RR  Quote
12-31-2015 04:01 PM  3 years ago
Andy from Sandy

rrElite Veteran

Bedfordshire, UK

MyPosts All Forum Topic
I took it back to the shop where I bought it from. It will go back to the distributor who have a repair facility.

Hopefully there is a connection to the processor and the firmware can be loaded again.

Worst case it will need a new main pcb. Worst, worst case it mean getting a new one, but I will let you know.
SHARE  PM  EMAIL  GALLERY  Attn:RR  Quote
01-06-2016 01:14 AM  3 years ago
Trickycopter

rrApprentice

Tulsa, Oklahoma

MyPosts All Forum Topic
where can I find what was updated with v6.Synergy E7 AMA member Team Old Farts citizen 401 www.trickycopterrc.blogspot.com
SHARE  PM  EMAIL  GALLERY  Attn:RR  Quote
01-06-2016 01:42 AM  3 years ago
knightofcarnage

rrElite Veteran

chicago

MyPosts All Forum Topic
SHARE  PM  EMAIL  GALLERY  Attn:RR  Quote
01-21-2016 01:06 PM  3 years ago
vburge

rrApprentice

Alabaster, Alabama - US

MyPosts All Forum Topic
Any news about the Castle ESC integration?

I have been using the E-Fuelgauge for mah consumption and it works great.
http://shop.tje.dk/catalog/
Synergy 516
Graupner
Xnova
SHARE  PM  EMAIL  Attn:RR  Quote
02-29-2016 11:15 PM  3 years ago
knightofcarnage

rrElite Veteran

chicago

MyPosts All Forum Topic
Ok Castle has released the telemetry adapter.
Its $49.99 (a fair price)

Watch at YouTube

SHARE  PM  EMAIL  GALLERY  Attn:RR  Quote
03-01-2016 02:05 PM  3 years ago
rpat

rrElite Veteran

Weirton, W. Va.

MyPosts All Forum Topic
So you can use this one instead of Futaba ?trex 700fbl cal30,minititan,, trx600fbl,trex250,logo 500,Velocity N2
SHARE  PM  EMAIL  GALLERY  Attn:RR  Quote
03-01-2016 08:15 PM  3 years ago
knightofcarnage

rrElite Veteran

chicago

MyPosts All Forum Topic
This gives you a lot more info and its straight from the horse mouth. Only think I don't like , there is not go way to secure it. I guess I can use a heat shrik or 3d print something. I would not like the connection to vibrate apart mid air.

Well Little bit of a bummer (No battery consumption, even if it was just a estimate)

Battery Voltage You will be able to see the voltage state of your battery during flight and respond appropriately to deteriorating conditions or alarms you’ve programmed in your radio.

Battery Current Reduce the load (throttle usually) to prevent an over-current shut down and know immediately if your consuming too much current in a particular maneuver.

Motor Power Output This is the percentage of full power your ESC is delivering to your motor.

RPM Ensure you are within acceptable parameters, without the use of a tachometer.

BEC Voltage Monitor your BEC voltage and its stability to the RX even under different loads from different servos.

ESC Temperature ESC temperature monitoring can eliminate a potential thermal shut down.

Battery Ripple Just how hard are the capacitors, FETS, and internal components working with your set up, excessive ripple can cause internal heating of batteries. Excessive heat is harmful to the components and it can ultimately kill the controller.
SHARE  PM  EMAIL  GALLERY  Attn:RR  Quote
03-24-2016 01:11 PM  3 years ago
Andy from Sandy

rrElite Veteran

Bedfordshire, UK

MyPosts All Forum Topic
Well it has taken some time but I have my transmitter back.

Ripmax who are the UK importer and distributor for Futaba were taking their time but was unable to either find the fault or get the parts to fix it so they have given me a brand new transmitter.

I would like to thank my LHS Inwood Models and Ripmax for resolving this and without charging me anything for it.
SHARE  PM  EMAIL  GALLERY  Attn:RR  Quote
03-26-2016 10:25 PM  3 years ago
Romak

rrApprentice

Scotland

MyPosts All Forum Topic
Hi Andy, thanks for letting us know. Good outcome. Nice to hear that Ripmax have replaced your tx. Well done to all.Rod
14sg....... ;-)
SHARE  PM  EMAIL  HOMEPAGE  GALLERY  Attn:RR  Quote
WATCH
 2 pages [ <<    <     1     ( 2 )    >    >> ] 5326 views POST REPLY
HomeRC & Power✈️Aircraft🚁HelicopterRadio - Futaba FASST › New firmware for 14sg version 6.0
 Print TOPIC  Make Suggestion 

 6  Topic Subscribe

Thursday, July 18 - 1:29 am - Copyright © 2000-2019 RunRyder   EMAILEnable Cookies

Login Here
 New Subscriptions 
 Buddies Online