RunRyder RC
 1 page 1419 views POST REPLY
FPV Racing
› just had to build one, Cruzroys clone Tarot 250
10-16-2015 02:28 AM  34 months agoPost 1
raptornoobrrVeteran - shrewsbury. ma. u.s.a. - My Posts: All  Forum  Topic

Robocat 270.....under 200.... except DX7s.....

spektrum dxmx orange mini sat
RDX led kit
shrink tubing
pulse 2200 mah 40c

let the tuning begin

Robocat 270mm 4-Axis Carbon Fiber Mini Quadcopter
- Wheelbase: 270mm
- Material: 100% Carbon fiber
- Removable hood make from shock-absorbing PC materials
- Flying weight: 410~430 (Battery excluded)
- Model net weight: 190g
- Hood color: GREEN
- 1.5mm thick fuselage & 3mm thick arms
- No assembled,just kit

RHD 2204 2300KV Motor:
- Light weight design
- Longer duration of flight
- Low CG Design, decreasing vibration when motor runs
- Using Japanese NMB ball bearing, Japanese Kawasaki stator, Ndfeb with strong magnetic and high temperature resistance, decreasing heat generation during pperation, increasing efficiency.
- CW and CCW Propeller adapters, holding the propellers tight.
- Designed for mini multicopters, better flight performance

- KV: 2300
- Max Trust: 408g
- No. of cell: 2-3S
- Framework: 12N14P
- Propeller: 5" - 6"
- Length: 31.5mm
- Shaft: 3mm
- Diameter: 28mm
- Weight: 25g

RHD SimonK 12A Brushless ESC Speed Controller
- Based on Simon K firmware, further optimized to the perfect drive performance.
- Low-voltage protection, over-heat protection and self-check functions.
- Separate power supply for MCU and BEC, enhancing the ESC’s ability of eliminating magnetic interference.
- Parameters of the ESC can be set via program card or transmitter.
- Throttle range can be set to be compatible with different receivers.
- Equipped with built-in linear BEC or switch BEC.
- Max speed: 210,000 rpm for 2-pole, 70,000 rpm for 6-pole, 35,000 rpm for 12-pole.

- Continuous Current: 12A
- Burst current (10S): 16A
- Li-xx Battery (cell): 2-4Cell
- Dimension (L*W*H): 21mm x 22mm x 4mm
- Weight wires Included: 12g
- BEC Mode: Linear
- BEC Output: 1A/5V
- Programmable: Yes

CC3D Flight Controller Introduction:
OpenPilot is a next-generation Open Source UAV autopilot. It is a highly capable platform for multi-rotor craft, helicopters, as well as fixed wing aircraft. It has been designed from the ground up by a community of passionate developers from around the globe, with its core design principals being quality, safety, and ease of use. Simplicity does not come with any compromises either: with no hard-coded settings, a complete flight plan scripting language and other powerful features, OpenPilot is an extremely capable UAV autopilot platform.

- Robocat 270mm FPV Quadcopter Frame x1
- ESC Connection Board x1
- RHD 2204 2300kv Brushless Motor x4
- RHD 12A Simonk ESC x4
- 5030 Propeller CW&CCW x4
- CC3D Flight Control With Case x1

10-16-2015 11:32 AM  34 months agoPost 2

rrKey Veteran

Hampshire England

My Posts: All  Forum  Topic

Very nice welcome to the quad club

The world is round you can run but you will always end up where you started from

10-16-2015 01:06 PM  34 months agoPost 3


shrewsbury. ma. u.s.a.

My Posts: All  Forum  Topic

yeah cute like a volkswagon bug
but tip to all noobs......if you have a open pilot....use there site for the vimeo videos for support......i went though all youtube vids and setups are pretty basic and ok, but when it comes to PID's and tuning your wasting your time.....the got good tutorials, finally got it to fly good.....still got tweeks to do for leveling.....but its good......caz i was WTF's a PID......

 1 page 1419 views POST REPLY
FPV Racing
› just had to build one, Cruzroys clone Tarot 250
 Print TOPIC  Make Suggestion 

 3  Topic Subscribe

Sunday, August 19 - 6:46 pm - Copyright © 2000-2018 RunRyder   EMAILEnable Cookies

Login Here
 New Subscriptions 
 Buddies Online