RunRyder RC
WATCH
 1 page 801 views POST REPLY
HomeRC & PowerAircraftHelicopterFlybarless Rotor Head SystemsV-Bar › V Bar Initalizing
09-06-2015 10:50 PM  3 years agoPost 1
Terminator

rrApprentice

Atlanta, ga

My Posts: All  Forum  Topic

I have the green USB and the green connection icon but when the system Start initializing it stall. I hope someone can lead me in the right direction to fix this.
Thanks
Terry

PM  EMAIL  GALLERY  Attn:RR  Quote
09-07-2015 06:55 AM  3 years agoPost 2
Sam2b

rrElite Veteran

Tacoma, WA

My Posts: All  Forum  Topic

Please describe "stall." We need to better know what is happening. Thanks.

_Sam B_

PM  EMAIL  HOMEPAGE  GALLERY  Attn:RR  Quote
09-07-2015 09:47 AM  3 years agoPost 3
Terminator

rrApprentice

Atlanta, ga

My Posts: All  Forum  Topic

It would start initializing but will never finish the process. The screen freezes.

Thanks

PM  EMAIL  GALLERY  Attn:RR  Quote
09-07-2015 01:47 PM  3 years agoPost 4
Ronald Thomas

rrMaster

Gainesville, Fl, USA

My Posts: All  Forum  Topic

Is the sensor plugged in?

Team MikadoUSA 480XXTreme, 550SX, 600SX, 700XXTreme, 800XXTreme!!

PM  EMAIL  GALLERY  Attn:RR  Quote
09-07-2015 07:12 PM  3 years agoPost 5
Terminator

rrApprentice

Atlanta, ga

My Posts: All  Forum  Topic

I'm embarrassed to say but no I have not tried it with the sensor attached. I will try this once I get home.

PM  EMAIL  GALLERY  Attn:RR  Quote
09-07-2015 08:00 PM  3 years agoPost 6
Ronald Thomas

rrMaster

Gainesville, Fl, USA

My Posts: All  Forum  Topic

That is the problem Plug it in (pay attention to polarity and the correct port) and then it should connect...

Team MikadoUSA 480XXTreme, 550SX, 600SX, 700XXTreme, 800XXTreme!!

PM  EMAIL  GALLERY  Attn:RR  Quote
09-08-2015 12:58 AM  3 years agoPost 7
Terminator

rrApprentice

Atlanta, ga

My Posts: All  Forum  Topic

Thanks
Ronald every thing is working Know.

PM  EMAIL  GALLERY  Attn:RR  Quote
09-12-2015 11:18 PM  3 years agoPost 8
Terminator

rrApprentice

Atlanta, ga

My Posts: All  Forum  Topic

OK gentleman having problems again. when going through the setup wizard on the v bar it is showing my pitch on channel 6 when it should be on channel 3. When setting up the radio adjusting the sub trim to get zero on the v bar for pitch it will adjust the throttle which should be on six. I'm assuming this have something to do with the collective. Please direct me in the right direction.

Thanks
Terry

PM  EMAIL  GALLERY  Attn:RR  Quote
09-13-2015 02:38 AM  3 years agoPost 9
Sam2b

rrElite Veteran

Tacoma, WA

My Posts: All  Forum  Topic

Hello, Terminator. I'm guessing it is a simple confusion. The throttle and pitch channels will move together in your transmitter (channels 3 and 6). Verify this by looking at your throttle curve and pitch curve; both are likely linear. Therefore, you are ok in the vbar. Confirm throttle and pitch are truly on the expected channel by changing the curve on throttle to be flat (zero), and leave the pitch linear (-100, +100). Then you should see the vbar pitch channel moving, and not the throttle channel. That will confirm what I'm saying.

If I'm way off, my apologies.

_Sam B_

PM  EMAIL  HOMEPAGE  GALLERY  Attn:RR  Quote
09-13-2015 05:30 PM  3 years agoPost 10
Terminator

rrApprentice

Atlanta, ga

My Posts: All  Forum  Topic

Understand Same2b. The problem is when I adjust channel three for pitch the throttle is what being adjusted on the v bar. I have the same thing happen when I adjust pitch curve. It seems that the channel assignment in the v bar is incorrect. Please give some directions.

Thanks
Terry

PM  EMAIL  GALLERY  Attn:RR  Quote
09-13-2015 09:52 PM  3 years agoPost 11
Sam2b

rrElite Veteran

Tacoma, WA

My Posts: All  Forum  Topic

Hi, Terry Terminator. That is correct:
  • channel 3 is the throttle
  • channel 6 is collective pitch
.
Given those facts, please check your configuration again, and reply with what you find.

_Sam B_

PM  EMAIL  HOMEPAGE  GALLERY  Attn:RR  Quote
09-14-2015 12:05 AM  3 years agoPost 12
Terminator

rrApprentice

Atlanta, ga

My Posts: All  Forum  Topic

Ok I understand. Should I connect the pitch servo to channel 3 or 6. The v bar is showing I should connect it to three. I have only used beasts and finding this to be a little confusing. Sorry to be a pest.

PM  EMAIL  GALLERY  Attn:RR  Quote
09-14-2015 12:52 AM  3 years agoPost 13
Nycatt

rrElite Veteran

New York

My Posts: All  Forum  Topic

The Servos themselves are connected the servo 1, 2 and 3 on the vbar unit itself. In the software on the channel assignment screen 3 is throttle and 6 is pitch.




Team Synergy
Rail Blades
MKS Servos
Thunder Power
Vteam

PM  EMAIL  HOMEPAGE  GALLERY  Attn:RR  Quote
09-14-2015 01:28 AM  3 years agoPost 14
Terminator

rrApprentice

Atlanta, ga

My Posts: All  Forum  Topic

Just making sure I understand. So I should change my channel three in my radio to throttle and six to pitch.
Thanks
Terry

PM  EMAIL  GALLERY  Attn:RR  Quote
09-14-2015 01:53 AM  3 years agoPost 15
Nycatt

rrElite Veteran

New York

My Posts: All  Forum  Topic

Ok I'm assuming your using a sbus receiver. 6203 or 6303sb When you bind don't realocate the channels. Also make sure you bind as Multi in the radio.

Go to servo monitor in the radio and you should see

1 Aileron
2 Elevator
3 Throttle (make sure to reverse)
4 Tail/Rudder
5 Gyro
6 Pitch
7 Gov




Team Synergy
Rail Blades
MKS Servos
Thunder Power
Vteam

PM  EMAIL  HOMEPAGE  GALLERY  Attn:RR  Quote
09-14-2015 06:04 AM  3 years agoPost 16
Sam2b

rrElite Veteran

Tacoma, WA

My Posts: All  Forum  Topic

Terry, Are you using Futaba S-bus to connect to the Vbar?

If yes, you have the ability to change the channel number in the Vbar software to coincide with the correct channel in your transmitter (the same channel number shown in the Function menu). But first what you must be certain about is when you look at either the throttle curve or collective pitch curve screens on the transmitter that they reflect the same movement as the blue bars moving in the Vbar software's Receiver tab.

I request for you to take a quick picture of your transmitter's Function menu so we can see the channel numbers and respective descriptions. Also take a picture of your Vbar software from the Receiver tab. Reply here and attach those pictures to let us see what you have, please. Otherwise, we might be misunderstanding each other.

_Sam B_

PM  EMAIL  HOMEPAGE  GALLERY  Attn:RR  Quote
09-14-2015 04:43 PM  3 years agoPost 17
Ronald Thomas

rrMaster

Gainesville, Fl, USA

My Posts: All  Forum  Topic

For Futaba, change it in the radio...

Team MikadoUSA 480XXTreme, 550SX, 600SX, 700XXTreme, 800XXTreme!!

PM  EMAIL  GALLERY  Attn:RR  Quote
09-14-2015 08:18 PM  3 years agoPost 18
Terminator

rrApprentice

Atlanta, ga

My Posts: All  Forum  Topic

Thanks guys I was able to get it figured out once I got the channel assignment's down. It's a little different then the beastX. Had to change them in my radio. Thanks again.

PM  EMAIL  GALLERY  Attn:RR  Quote
WATCH
 1 page 801 views POST REPLY
HomeRC & PowerAircraftHelicopterFlybarless Rotor Head SystemsV-Bar › V Bar Initalizing
 Print TOPIC  Make Suggestion 

 3  Topic Subscribe

Wednesday, September 26 - 4:21 pm - Copyright © 2000-2018 RunRyder   EMAILEnable Cookies

The RC discussion world needs to consolidate. RR is now one choice for that. Its software is cutting edge. It hosts on-topic advertising. Help RR increase traffic buy making suggestions, posting in RR's new areas (sites) and by spreading the word.

The RunRyder Difference

• Category system to allow Rep/Vendor postings.
• Classifieds with sold (hidden) category.
• Classifieds with separate view new.
• Answer PMs offsite via email reply.
• Member gallery photos with advanced scripting.
• Gallery photo viewer integrated into postings.
• Highly refined search with advanced back end.
• Hosts its own high end fast response servers.
• Hosts thousands of HD event coverage videos.
• Rewrote entire code base with latest technology.
• No off-topic (annoying) click bait advertising.
Login Here
 New Subscriptions 
 Buddies Online