RunRyder RC
WATCH
 1 page 819 views Post Reply
HomeRC & Power✈️Aircraft🚁HelicopterRadio - Servo - Gyro - Gov - Batt › Original throttle jockey pro
06-17-2015 05:38 PM  5 years ago
Topic Vote0Post 1
Jamovich

rrVeteran

Maryland, USA

MyPosts All Forum Topic
Original throttle jockey pro
hi guys

I got a the first version of the throttle jockey pro and I wish to reconfigure it for a new setup. Problem is I cannot seem to enter calibration mode when I flick the aux (flight phase) switch on/off/on during the first 3 seconds when the RX is turned on as according to the instructions. ATV on the aux channel is 100/100 and 110/110 on the throttle end points. I'm using a t-14mz with 2.4ghz

Thanks for any inputs
SHARE  PM  EMAIL  GALLERY  Attn:RR  Quote
06-25-2015 10:59 AM  5 years ago
Richardmid1

rrProfessor

Leeds, England

MyPosts All Forum Topic
Ridiculously complicated to setup! Anyway, are there any lights that change when you flick the AUX channel switch? Is the AUX channel switch assigned to the AUX channel? Have you tried 0/100 or 100/0 in the AUX channel travel adjust?60% of the time, it works every time!
SHARE  PM  EMAIL  HOMEPAGE  GALLERY  Attn:RR  Quote
06-25-2015 11:49 AM  5 years ago
ICUR1-2

rrElite Veteran

Ottawa, Ontario

MyPosts All Forum Topic
try reversing the aux channel
SHARE  PM  EMAIL  GALLERY  Attn:RR  Quote
10-30-2015 09:47 PM  5 years ago
allns47

rrKey Veteran

Richmond IN.

MyPosts All Forum Topic
I ran into this also,,,,when calibrating,,,,the channel u have the gain on you must set it to -100 and +100.....Once calabration is complete,,,go back to whatever channel u have gain plugged in and set the gain values to the head speed you want,,,If you have a 2 position switch you would set one point to 0 which will turn tjpro off antd the other position to whatever headspeed you want,,,,,if you have a 3 position switch during calabration you need to do set it as -100 0 +100,,,after calabration you need to set the switch to 0 and then the other 2 positions you can have to different head speeds..
SHARE  PM  EMAIL  GALLERY  Attn:RR  Quote
10-31-2015 02:22 AM  5 years ago
dkshema

rrMaster

Cedar Rapids, IA

MyPosts All Forum Topic
Ridiculously complicated to setup!
You mean turn on power, flip a switch back and forth a couple of times, full throttle, low throttle, flip the switch again and you're done is ridiculously complicated?

You usually will have a problem if you use a channel with a three position switch to get it into cal mode.
-----
Dave

* Making the World Better -- One Helicopter at a time! *

Team Heliproz
SHARE  PM  EMAIL  GALLERY  Attn:RR  Quote
11-02-2015 12:47 PM  5 years ago
allns47

rrKey Veteran

Richmond IN.

MyPosts All Forum Topic
no problem using a 3 postion switch,,during calabration just make sure u set the switch values at -100,,,0,,,,+100,,never adjust the atvs...leave the -100 +100,,,after you calabrate set the switch to 0...the next two values whatever u want the head speed,,,example 0....64...72
SHARE  PM  EMAIL  GALLERY  Attn:RR  Quote
WATCH
 1 page 819 views Post Reply
HomeRC & Power✈️Aircraft🚁HelicopterRadio - Servo - Gyro - Gov - Batt › Original throttle jockey pro
Print TOPIC

 5  Topic Subscribe

Friday, May 7 - 11:10 am - Copyright © 2000-2021 RunRyder   EMAILEnable Cookies

Login Here
 New Subscriptions 
 Buddies Online