RunRyder RC
WATCH
 1 page 759 views POST REPLY
HomeRC & Power✈️Aircraft🚁HelicopterFlybarless Rotor Head SystemsFutaba CGY › CGY 750 not Initializing
06-03-2015 12:41 AM  4 years ago
Topic Vote0Post 1
Trickycopter

rrApprentice

Tulsa, Oklahoma

MyPosts All Forum Topic
CGY 750 not Initializing
I am trying to setup a CGY 750 on a trex 450 when I power up the unit it hangs on Id# and version 1.4 should I never see the helicopter doing back flips is there something wrong with my unit or am I doing something wrong?
Synergy E7 AMA member Team Old Farts citizen 401 www.trickycopterrc.blogspot.com
SHARE  PM  EMAIL  GALLERY  Attn:RR  Quote
06-03-2015 01:11 AM  4 years ago
Mark Dean

rrApprentice

Maryland

MyPosts All Forum Topic
Sbus mode
The unit won't init until the receiver sends a signal. What receiver are you using? You may need to set the receiver mode to s-bus.

Mark
Team Synergy Field Representative, Rail Blades, Scorpion Power Systems
SHARE  PM  EMAIL  GALLERY  Attn:RR  Quote
06-03-2015 01:22 AM  4 years ago
Trickycopter

rrApprentice

Tulsa, Oklahoma

MyPosts All Forum Topic
I am using the R7008 the one that came with the 14SGSynergy E7 AMA member Team Old Farts citizen 401 www.trickycopterrc.blogspot.com
SHARE  PM  EMAIL  GALLERY  Attn:RR  Quote
06-03-2015 02:26 AM  4 years ago
Trickycopter

rrApprentice

Tulsa, Oklahoma

MyPosts All Forum Topic
Do I need a special cable to connect the Sbus ports togetherSynergy E7 AMA member Team Old Farts citizen 401 www.trickycopterrc.blogspot.com
SHARE  PM  EMAIL  GALLERY  Attn:RR  Quote
06-03-2015 02:29 AM  4 years ago
Mark Dean

rrApprentice

Maryland

MyPosts All Forum Topic
Excellent. It is not set to use sbus by default.

No special cables needed. Use the male to male servo wire that comes with the cgy in the Sbus port from receiver to the cgy750.

Now for the receiver mode you will want to use either mode b or d. These are sbus enabled. The instructions tell you how to enable sbus mode with a little chart to explain the differences.

Press and hold down the Link/Mode button on the R7008SB receiver.
Turn the receiver on while holding down the Link/Mode button. After power up, the button can be released.
The LED should now be blinking red
Each press of the Mode/Link button advances the receiver to the next mode.
When you reach the mode that you wish to operate in(eg. Two flashes is b and 4 flashes is d), press and hold the Mode/Link button for more than 2 seconds.

Once locked into the correct mode the LED will change to a solid color.
Please cycle the receiver(s) power off and back on again after changing the Channel Mode.

Mark
Team Synergy Field Representative, Rail Blades, Scorpion Power Systems
SHARE  PM  EMAIL  GALLERY  Attn:RR  Quote
06-03-2015 03:17 AM  4 years ago
Trickycopter

rrApprentice

Tulsa, Oklahoma

MyPosts All Forum Topic
I set the receiver got two red lights flashing still not getting it to work.

Synergy E7 AMA member Team Old Farts citizen 401 www.trickycopterrc.blogspot.com
SHARE  PM  EMAIL  GALLERY  Attn:RR  Quote
06-03-2015 03:48 AM  4 years ago
Trickycopter

rrApprentice

Tulsa, Oklahoma

MyPosts All Forum Topic
I got it did not have the receiver in sbus mode did not read all the instuctions above. thanks for the help.Synergy E7 AMA member Team Old Farts citizen 401 www.trickycopterrc.blogspot.com
SHARE  PM  EMAIL  GALLERY  Attn:RR  Quote
06-03-2015 04:07 AM  4 years ago
Mark Dean

rrApprentice

Maryland

MyPosts All Forum Topic
No problem.

Mark
Team Synergy Field Representative, Rail Blades, Scorpion Power Systems
SHARE  PM  EMAIL  GALLERY  Attn:RR  Quote
WATCH
 1 page 759 views POST REPLY
HomeRC & Power✈️Aircraft🚁HelicopterFlybarless Rotor Head SystemsFutaba CGY › CGY 750 not Initializing
 Print TOPIC  Make Suggestion 

 2  Topic Subscribe

Tuesday, February 18 - 9:17 pm - Copyright © 2000-2020 RunRyder   EMAILEnable Cookies

Login Here
 New Subscriptions 
 Buddies Online