RunRyder RC
WATCH
 1 page 662 views POST REPLY
HomeAircraftHelicopter
e-
Align
T-REX 450 › Bind or Radio reset
01-07-2015 03:43 AM  3 years agoPost 1
pit

rrNovice

Cleveland, OH USA

My Posts: All  Forum  Topic

Hey guys. I am going to install new set of cyclic servo(diff brand HV-servos), my gyro is 3gx stock Trex 450 Pro. Do I need to rebind (the heli and radio again) if I'm going to reset my tx?

thank you in advance.

PM  EMAIL  Attn:RR  Quote
01-07-2015 04:46 AM  3 years agoPost 2
dkshema

rrMaster

Cedar Rapids, IA

My Posts: All  Forum  Topic

It's not necessary to rebind your rx when you replace servos. But as I recall, you're switching servo brands. In that case, just re-bind.

This question is similar to your question about being able to just bolt on new servos without really doing any of the setup required of the flybarless controller.

Frankly, binding is a ten second affair and allows you to make sure your failsafe settings are what you want them to be, and the FBL controller setup takes maybe 10-15 minutes out of your day.

If you want a helicopter that just flies "so-so", you skip the decent setup steps. If you want a heli that flies well and is predictable, you spend a few more minutes going through the setup steps.

-----

Just re-read and saw the "going to reset my TX" statement. Bind the RX, set your failsafe settings at that time.

-----
Dave

* Making the World Better -- One Helicopter at a time! *

Team Heliproz

PM  EMAIL  GALLERY  Attn:RR  Quote
01-07-2015 01:17 PM  3 years agoPost 3
jsenicka

rrProfessor

Eagle River, WI

My Posts: All  Forum  Topic

You will need a full setup (at least servo centering, direction, throw, etc)

Jim Senicka
Team Manager, GrandRC Flight Team

PM  EMAIL  GALLERY  Attn:RR  Quote
01-07-2015 02:03 PM  3 years agoPost 4
rcmiket

rrVeteran

El Paso,Texas

My Posts: All  Forum  Topic

I would do a rebind after your new servo set up since they are a different brand and so on and for sure on a transmitter reset. Anytime I change anything major I do a rebind.

Mike

"When Inverted down is up and up is expensive"

PM  EMAIL  GALLERY  Attn:RR  Quote
01-07-2015 02:30 PM  3 years agoPost 5
pit

rrNovice

Cleveland, OH USA

My Posts: All  Forum  Topic

It's not necessary to rebind your rx when you replace servos. But as I recall, you're switching servo brands. In that case, just re-bind.
This question is similar to your question about being able to just bolt on new servos without really doing any of the setup required of the flybarless controller.
Frankly, binding is a ten second affair and allows you to make sure your failsafe settings are what you want them to be, and the FBL controller setup takes maybe 10-15 minutes out of your day.
If you want a helicopter that just flies "so-so", you skip the decent setup steps. If you want a heli that flies well and is predictable, you spend a few more minutes going through the setup steps.
-----
Just re-read and saw the "going to reset my TX" statement. Bind the RX, set your failsafe settings at that time.
-----
Dave

> Yes Sir Dave, I was just a little confused sometimes, and hesitant to ask questions. My servos just arrived and just excited, though I cant really fly it yet since it's snowing here and cold..but at the same time want to be ready for the summer...or maybe when it gets a little warmer...... So I'll just reset my radio and bind and do all the set ups.....thankspit

You will need a full setup (at least servo centering, direction, throw, etc)
Jim Senicka

> Ok. Thanks Sir Jim..

I would do a rebind after your new servo set up since they are a different brand and so on and for sure on a transmitter reset. Anytime I change anything major I do a rebind.

> rcmiket, yes will rebind to make sure.

PM  EMAIL  Attn:RR  Quote
WATCH
 1 page 662 views POST REPLY
HomeAircraftHelicopter
e-
Align
T-REX 450 › Bind or Radio reset
 Print TOPIC  Make Suggestion 

 2  Topic Subscribe

Wednesday, November 21 - 6:02 am - Copyright © 2000-2018 RunRyder   EMAILEnable Cookies

The RC discussion world needs to consolidate. RR is now one choice for that. Its software is cutting edge. It hosts on-topic advertising. Help RR increase traffic buy making suggestions, posting in RR's new areas (sites) and by spreading the word.

The RunRyder Difference

• Category system to allow Rep/Vendor postings.
• Classifieds with sold (hidden) category.
• Classifieds with separate view new.
• Answer PMs offsite via email reply.
• Member gallery photos with advanced scripting.
• Gallery photo viewer integrated into postings.
• Highly refined search with advanced back end.
• Hosts its own high end fast response servers.
• Hosts thousands of HD event coverage videos.
• Rewrote entire code base with latest technology.
• No off-topic (annoying) click bait advertising.
Login Here
 New Subscriptions 
 Buddies Online