RunRyder RC
WATCH
 1 page 1618 views POST REPLY
HomeRC & Power✈️Aircraft🚁HelicopterRadio - Graupner › Setting throttle curves on MC-20 or MC-16
12-10-2014 08:09 PM  5 years ago
Topic Vote0Post 1
Jim Cimino

rrKey Veteran

NE Pennsylvania

MyPosts All Forum Topic
Setting throttle curves on MC-20 or MC-16
I am trying to set some throttle curves for 3d flight on my electric Goblin. I have created two new phases and set the throttle curves, but the #6 channel (throttle) does not respond like the throttle curve. In normal mode, I can see the linear throttle curve but when I switch to either of the other phases the servo movement is nothing like the curve. For example: I set the curve for 3d to L=90, 50%=75, and H=90. But when I watch the servo movement on the radio it goes from about 125% down to near 0 and then stays right about there, does not come back up to 125%.
Team Synergy, Team Scorpion, No good deed goes unpunished
SHARE  PM  EMAIL  GALLERY  Attn:RR  Quote
12-10-2014 08:30 PM  5 years ago
Maizor

rrNovice

Rogaland , Norway

MyPosts All Forum Topic
Hei

I know the MC20 pretty good. Where are you setting you curves? In the helicopter mixer menu? Can you see your phases change in the C1-Thottle ?
Sylphide EX FBL, Sylphide MB391, TDR
SHARE  PM  EMAIL  Attn:RR  Quote
12-10-2014 08:50 PM  5 years ago
Jim Cimino

rrKey Veteran

NE Pennsylvania

MyPosts All Forum Topic
That is where I am setting them. With the values I am using I would expect the servo travel view to show me channel 6 moving from say +125 to +90 and back to +125 but that is not what happens. The bottom shows the three different modes that I have set, normal, aerobatic and 3d with separate throttle curves for each, but the only one that moves correctly is normal mode.Team Synergy, Team Scorpion, No good deed goes unpunished
SHARE  PM  EMAIL  GALLERY  Attn:RR  Quote
12-10-2014 09:05 PM  5 years ago
Maizor

rrNovice

Rogaland , Norway

MyPosts All Forum Topic
Hmm while playing here now with my MC 20 i see something similar but only on one model my forza 450. My sylphides show me what i would expect in the servo monitor. I know my forza curves work i think this could be a bug. I will ask in GH lounge. If you not member thats a good place to get graupner news. Its all in german but. I will come back after asking aroundSylphide EX FBL, Sylphide MB391, TDR
SHARE  PM  EMAIL  Attn:RR  Quote
12-10-2014 09:12 PM  5 years ago
Maizor

rrNovice

Rogaland , Norway

MyPosts All Forum Topic
If you look in the C1-trottle menu do you see the "output" change the way you want? In the different phases

And also what reciver you using?
Sylphide EX FBL, Sylphide MB391, TDR
SHARE  PM  EMAIL  Attn:RR  Quote
12-10-2014 11:34 PM  5 years ago
Jim Cimino

rrKey Veteran

NE Pennsylvania

MyPosts All Forum Topic
I am using a graupner Hott 8 channel receiver. The input and outputs on the c1- throttle show correct numbers when the throttle stick moves. When I look at the assistant software for my controller showing the throttle moving the same way as the servo movement page on the radio which is not what the curve shows.Team Synergy, Team Scorpion, No good deed goes unpunished
SHARE  PM  EMAIL  GALLERY  Attn:RR  Quote
12-28-2014 02:17 AM  5 years ago
Jim Cimino

rrKey Veteran

NE Pennsylvania

MyPosts All Forum Topic
Ok, figured out the throttle curve issue. I still had the throttle set to global instead of phase. All is good now.Team Synergy, Team Scorpion, No good deed goes unpunished
SHARE  PM  EMAIL  GALLERY  Attn:RR  Quote
03-06-2015 09:40 PM  4 years ago
ren

rrVeteran

Houston, TX

MyPosts All Forum Topic
Can you post a picture of the screen where that setting?
Please
SHARE  PM  EMAIL  GALLERY  Attn:RR  Quote
03-19-2015 04:23 AM  4 years ago
Jim Cimino

rrKey Veteran

NE Pennsylvania

MyPosts All Forum Topic
The setting is under control settings.Team Synergy, Team Scorpion, No good deed goes unpunished
SHARE  PM  EMAIL  GALLERY  Attn:RR  Quote
WATCH
 1 page 1618 views POST REPLY
HomeRC & Power✈️Aircraft🚁HelicopterRadio - Graupner › Setting throttle curves on MC-20 or MC-16
 Print TOPIC  Make Suggestion 

 1  Topic Subscribe

Sunday, February 16 - 7:11 pm - Copyright © 2000-2020 RunRyder   EMAILEnable Cookies

Login Here
 New Subscriptions 
 Buddies Online