RunRyder RC
 2  Topic Subscribe
WATCH
 1 page 813 views POST REPLY
HomeAircraftHelicopterRadio - Mikado VBAR Control System › problem with governer
06-30-2014 12:43 AM  3 years agoPost 1
Charlie R

rrApprentice

Lafayette Ca

My Posts: All  Forum  Topic

I am converting my Synergy E7 to VBAR control and I am having a problem with the ( VBar "Silverline" 5.3 PRO now 6 ) VBAR governor ! I get the requested head speed ( heli sitting on ground no blades ) but if I play with the collective head speed drops off fast ,if I leave collective alone for a few seconds it returns to requested head speed . I turned gain down to 10 made no difference .I a am lost and am sure I missed something in set up , please help ! Heli was flying great on 5.3 ! speed controller is 04687 ESC YGE-160 , with governor adapter motor is Scorpion 4525-520KV
Thanks Charlie

Helicopters are a mass of rotating metal fatigue surrounding an oil leak !

PM  EMAIL  GALLERY  Attn:RR  Quote
06-30-2014 07:10 AM  3 years agoPost 2
kobe1kobe

rrNovice

smyrna, tennessee, u.s.a

My Posts: All  Forum  Topic

You can get faster help on vstabi.info, Just post it under vbar control..questions?, ask! Those guys are the experts!

PM  EMAIL  GALLERY  Attn:RR  Quote
06-30-2014 12:13 PM  3 years agoPost 3
Ronald Thomas

rrMaster

Gainesville, Fl, USA

My Posts: All  Forum  Topic

Did you calibrate the tx sticks fully in the tx and did you go through the ESC setup wizard? Did you relearn the throttle endpoints in the ESC?Lastly, when you finished the setup wizard, did you check to make sure the selection for which gov you are using in the tx is VBAR Gov? I found that it defaults back to "internal gov" when you go through the wizard and you need to change it…..Ron

Team MikadoUSA 480XXTreme, 550SX, 600SX, 700XXTreme, 800XXTreme!!

PM  EMAIL  GALLERY  Attn:RR  Quote
07-03-2014 01:58 AM  3 years agoPost 4
Charlie R

rrApprentice

Lafayette Ca

My Posts: All  Forum  Topic

Governer
So I could not figure it out so I put my question on Vstabi page and this is what I got .I don't understand why but it works great !

RV [ Private Nachricht ]
Re: Trouble with YGE & VBAR governer neu
01.07.2014 23:00:18 Moderator

Hello Charlie,

this is no trouble - it is just the throttle curve "behind the scenes" ;-)
This is a essential part of the governor - and makes it different from all others out there.
You will see the throttle curve and some Integral Loop parts working here - w/o blades, w/o load, w/o flying.

So - to check - it won't have this effect with zero collective/cyclic add in the Governor Setup - it is what i describe.

Just try in flight - not too much on the bench ;-)

regards (EN) / Gruss (DE)

Rainer Vetter

Helicopters are a mass of rotating metal fatigue surrounding an oil leak !

PM  EMAIL  GALLERY  Attn:RR  Quote
WATCH
 1 page 813 views POST REPLY
HomeAircraftHelicopterRadio - Mikado VBAR Control System › problem with governer
 Print TOPIC  Make Suggestion 

 2  Topic Subscribe

Tuesday, June 19 - 8:57 pm - Copyright © 2000-2018 RunRyder   EMAILEnable Cookies

Login Here
 New Subscriptions 
 Buddies Online