RunRyder RC
WATCH
 1 page 787 views POST REPLY
HomeAircraftHelicopterMain Discussion › helicommand HC3SX
03-11-2014 11:00 PM  4 years agoPost 1
gat2013

rrNovice

saint cloud, fl. -usa

My Posts: All  Forum  Topic

I just got this heli and i am wondering how to bind it to my 7s. My other heli has the beastx in it and i use the bind plug to do this but not sure with the helicommand?

PM  EMAIL  Attn:RR  Quote
03-11-2014 11:14 PM  4 years agoPost 2
Stephen Born

rrElite Veteran

USA

My Posts: All  Forum  Topic

Using a DSMX DX7s Tx, you will need a DSMX satellite. If a 450 class, use one satellite. If a 500 class or higher, use two satellites.

Bind the DX7s (DSMX) with the satellites (DSMX) as you normally would. The HC3-SX has two ports on the side for satellite wires. If using two satellites, be sure to have satellites at 90 degrees of each other and leave a 60mm distance between both.

PM  EMAIL  Attn:RR  Quote
03-11-2014 11:31 PM  4 years agoPost 3
fastflyer20

rrKey Veteran

N. Tonawanda, NY

My Posts: All  Forum  Topic

When you go through the setup wizard, it will tell you when to bind it.

Start off by downloading the latest software and firmware from the web site.

http://www.bavariandemon.com/en/ser...tware-firmware/

Tom
CAUTION - my posts are based on my experiences, yours may be different.

PM  EMAIL  GALLERY  Attn:RR  Quote
03-11-2014 11:38 PM  4 years agoPost 4
Stephen Born

rrElite Veteran

USA

My Posts: All  Forum  Topic

As stated by fastflyer20, the software will indicate the exact timing for the binding process.

Thanks for catching that for me Tom.

PM  EMAIL  Attn:RR  Quote
03-12-2014 12:02 AM  4 years agoPost 5
gat2013

rrNovice

saint cloud, fl. -usa

My Posts: All  Forum  Topic

the heli has both satellites in it. the heli is ready to fly i got it from a freind. i copyed his program to my radio i just need to get it binded to my radio. So i have to have the wire to plug into the helicommand and computer so i can bind it? because i didnt get it from him. I can order one if i need to. just want to make sure i am understanding all of this.

PM  EMAIL  Attn:RR  Quote
03-12-2014 12:12 AM  4 years agoPost 6
fastflyer20

rrKey Veteran

N. Tonawanda, NY

My Posts: All  Forum  Topic

I would strongly suggest setting it up yourself using the setup wizard, your TX needs to be calibrated which may be different than the one he set it up and it is best to make sure the throws are correct, etc.

Binding - there is no jumper plug, it is done through the software on the RC tab in the software. You will need the Helicommand USB cord, it is special.

Tom
CAUTION - my posts are based on my experiences, yours may be different.

PM  EMAIL  GALLERY  Attn:RR  Quote
03-12-2014 12:21 AM  4 years agoPost 7
gat2013

rrNovice

saint cloud, fl. -usa

My Posts: All  Forum  Topic

ok thanks Tom. i ordered the cable last night. i downloaded the software for the helicommand already and i ordered the cable last night. now when the cable gets here and i hook it up should i just go threw the whole setup with the heli like its never been flown. so its setup for my radio?

PM  EMAIL  Attn:RR  Quote
03-12-2014 12:49 AM  4 years agoPost 8
Stephen Born

rrElite Veteran

USA

My Posts: All  Forum  Topic

Yes. The software will indicate "when and how" movements of the toggle sticks. All sub-trims should be set on zero to give accurate readings.

PM  EMAIL  Attn:RR  Quote
03-12-2014 01:43 AM  4 years agoPost 9
gat2013

rrNovice

saint cloud, fl. -usa

My Posts: All  Forum  Topic

thank you guys very much.

PM  EMAIL  Attn:RR  Quote
WATCH
 1 page 787 views POST REPLY
HomeAircraftHelicopterMain Discussion › helicommand HC3SX
 Print TOPIC  Make Suggestion 

 2  Topic Subscribe

Saturday, August 18 - 9:33 pm - Copyright © 2000-2018 RunRyder   EMAILEnable Cookies

Login Here
 New Subscriptions 
 Buddies Online