RunRyder RC
WATCH
 1 page 879 views POST REPLY
HomeAircraftHelicopterRadio - Futaba FASST › FUTABA 750 GYRO INTER ACTION ON CYCLIC
10-10-2013 10:25 AM  4 years agoPost 1
gary saia

rrApprentice

chandler tx usa

My Posts: All  Forum  Topic

Hi futaba guru's , I have gottem my750 CGY set up with the 4 point ccpm , works perfect , then i let a friend from longview tx that has been flying the 750 , i asked him to help hooking up my gv-1 governor with my Futaba 14 sg radio, after he played with it , I notice it was a nightmare , up and down collective with swash cyclic inter action all over the place , orginallly i had it working fine , , so i got it back and went thru the entire menus resetting all values to stock , first off He changed s.bus basic map channels selection , so i put it back to stock assigments like in the manual , channels 1-8 , FIRST OFF THERE ARE NO MIXING OF CHANNELS IN MY 14 SG , I WENT THRU THE ENTIRE RADIO , ALSO I AM RUNNING A FLY BAR HEAD AND ACCORDING TO BEN MINOR , I SET ALL GYRO CYCLIC CONDITIONS TO NORMAL , AND REDUCE GAIN TO 0 gain , that is fine , , I GOT JUST ABOUT ALL IT WORKING PROPERLY , EXCEPT 1 THING , I GET A LITTLE LEFT AILERON CONTROL ONLY BACK CYCLIC ONLY , I GOT FORWARD , NO OTHER MOVEMENT, WHEN I GIVE LEFT OR RIGHT AILERON , NO FOR AND AFT MOVEMENT , ,,,, JUST ON BACK CYCLIC , WEIRD , ANY HELP, I AM PLANNING ON GOING THRU EVERY MENU AND RECHECK BEFORE I PULL OUT THE REST OF MY HAIR , GARY SAIA TEXAS , 817-812-7050, E-MAIL IS garyvsaia@gmail.com

PM  EMAIL  HOMEPAGE  GALLERY  Attn:RR  Quote
10-10-2013 12:25 PM  4 years agoPost 2
gary saia

rrApprentice

chandler tx usa

My Posts: All  Forum  Topic

fix it
all my friends , Uh !!

PM  EMAIL  HOMEPAGE  GALLERY  Attn:RR  Quote
11-10-2013 03:27 AM  4 years agoPost 3
wc_wickedclown (RIP)

rrProfessor

long beach calif

My Posts: All  Forum  Topic

interaction most of the time from the elevator

relocate elevator linkage 1 hole up or back

Insha Allah made in america

PM  EMAIL  HOMEPAGE  GALLERY  Attn:RR  Quote
11-10-2013 10:54 AM  4 years agoPost 4
Kloss08

rrApprentice

Bradford PA USA

My Posts: All  Forum  Topic

Does it perform this same issue on other models? You said your model has a flybar. Do you have the cyclic servos plugged in to the Cgy 750 or to the receiver.

Team Futaba
Team Pulse Batteries
Enjoy it today

PM  EMAIL  GALLERY  Attn:RR  Quote
11-11-2013 03:35 AM  4 years agoPost 5
Chris.C

rrVeteran

Hong Kong

My Posts: All  Forum  Topic

If yours have a flybar and not intend to use cyclic gyros in the 750(gain set to zero as you said), then I would use a 8 channel receiver, e.g. a 6208SB, plug the pitch, ele and ail servos directly into the receiver, 750 is just for the rudder gyro.

This way, I can set 14SG into whatever suits your swash plate other than H-1. You will have the "Swash" menu back and mix out interaction from there.

PM  EMAIL  GALLERY  Attn:RR  Quote
11-12-2013 01:57 AM  4 years agoPost 6
Dr.Ben

rrMaster

Richmond, VA, USA

My Posts: All  Forum  Topic

That will work. The same mixers are in the 750 if he would like to preserve full S.Bus implementation.

Ben Minor

Peak Aircraft/Team Minicopter Team Futaba Team Kontronik USA

PM  EMAIL  GALLERY  Attn:RR  Quote
WATCH
 1 page 879 views POST REPLY
HomeAircraftHelicopterRadio - Futaba FASST › FUTABA 750 GYRO INTER ACTION ON CYCLIC
 Print TOPIC  Make Suggestion 

 4  Topic Subscribe

Tuesday, July 17 - 2:01 pm - Copyright © 2000-2018 RunRyder   EMAILEnable Cookies

Login Here
 New Subscriptions 
 Buddies Online