RunRyder RC
WATCH
 1 page 1224 views POST REPLY
HomeAircraftHelicopterFlybarless Rotor Head SystemsV-Bar › vbar tail gain issue help
09-05-2013 05:20 AM  4 years agoPost 1
wc_wickedclown (RIP)

rrProfessor

long beach calif

My Posts: All  Forum  Topic

i've got the gain at 120 on my 700 and i'm not getting any wag

tail stops but not as hard and solid as think it should

Insha Allah made in america

PM  EMAIL  HOMEPAGE  GALLERY  Attn:RR  Quote
09-05-2013 07:13 AM  4 years agoPost 2
Kauaiguy

rrNovice

Hawaii

My Posts: All  Forum  Topic

Did you try and run the tail optimizer ?

I'd rather be flying!

PM  EMAIL  Attn:RR  Quote
09-05-2013 09:39 AM  4 years agoPost 3
Ronald Thomas

rrMaster

Gainesville, Fl, USA

My Posts: All  Forum  Topic

Did you try the "stop gains" in the expert menu as well?

Team MikadoUSA 480XXTreme, 550SX, 600SX, 700XXTreme, 800XXTreme!!

PM  EMAIL  GALLERY  Attn:RR  Quote
09-05-2013 06:57 PM  4 years agoPost 4
wc_wickedclown (RIP)

rrProfessor

long beach calif

My Posts: All  Forum  Topic

Kauaiguy
Did you try and run the tail optimizer ?
i have it enabled.
laughingstill
Did you try the "stop gains" in the expert menu as well?
no i have not touched them ill make a video of my settings and then hopefully you can give me some recomendation.

Insha Allah made in america

PM  EMAIL  HOMEPAGE  GALLERY  Attn:RR  Quote
09-05-2013 08:00 PM  4 years agoPost 5
Ronald Thomas

rrMaster

Gainesville, Fl, USA

My Posts: All  Forum  Topic

If the optimizer is on, turn it off before you start messing with settings. If not, the optimizer will change them as you fly again.

Team MikadoUSA 480XXTreme, 550SX, 600SX, 700XXTreme, 800XXTreme!!

PM  EMAIL  GALLERY  Attn:RR  Quote
09-05-2013 09:46 PM  4 years agoPost 6
wc_wickedclown (RIP)

rrProfessor

long beach calif

My Posts: All  Forum  Topic

laughingstill
If the optimizer is on, turn it off before you start messing with settings. If not, the optimizer will change them as you fly again.
thanks brother
what else would you recommend ?

Watch at YouTube

Insha Allah made in america

PM  EMAIL  HOMEPAGE  GALLERY  Attn:RR  Quote
09-05-2013 09:59 PM  4 years agoPost 7
Ronald Thomas

rrMaster

Gainesville, Fl, USA

My Posts: All  Forum  Topic

What tail servo., ball distance and blades are you using? Trex 700?
You can raise the stop gains on either end to make it stop harder but if the issue is mechanical then adjusting numbers won't help much.

Team MikadoUSA 480XXTreme, 550SX, 600SX, 700XXTreme, 800XXTreme!!

PM  EMAIL  GALLERY  Attn:RR  Quote
09-05-2013 10:11 PM  4 years agoPost 8
Kauaiguy

rrNovice

Hawaii

My Posts: All  Forum  Topic

Should turn off trim optimizer if your done there.you can setup the Vbar to have your tx select tail gain or program it on Vbar software.I think you select that from the menu to the right under banks,go to the bottom and select gyro,now you should be able to set it with the tx.Ive only had my Fubar for a little while.

I'd rather be flying!

PM  EMAIL  Attn:RR  Quote
09-05-2013 10:41 PM  4 years agoPost 9
Andy from Sandy

rrElite Veteran

Bedfordshire, UK

My Posts: All  Forum  Topic

Additional to laughingstill - What settings have you got for the left and right limits in the tail setup menu?

PM  EMAIL  GALLERY  Attn:RR  Quote
09-10-2013 02:55 AM  4 years agoPost 10
wc_wickedclown (RIP)

rrProfessor

long beach calif

My Posts: All  Forum  Topic

how do i disable the tain gyro gain on the vbar ?

i think when you enable the bank switching that disables the gyro
function from the tx then you just use the vbar menu to control the gain correct ?

Insha Allah made in america

PM  EMAIL  HOMEPAGE  GALLERY  Attn:RR  Quote
09-12-2013 01:37 PM  4 years agoPost 11
Nycatt

rrElite Veteran

New York

My Posts: All  Forum  Topic

Set the drop down box on the bank switching section to "gyro" then assign the channel your using on Aux 2 to your gyro control on your TX.




Team Synergy
Rail Blades
MKS Servos
Thunder Power
Vteam

PM  EMAIL  HOMEPAGE  GALLERY  Attn:RR  Quote
09-12-2013 02:41 PM  4 years agoPost 12
wc_wickedclown (RIP)

rrProfessor

long beach calif

My Posts: All  Forum  Topic

Nycatt
Set the drop down box on the bank switching section to "gyro" then assign the channel your using on Aux 2 to your gyro control on your TX.
Tanks

Insha Allah made in america

PM  EMAIL  HOMEPAGE  GALLERY  Attn:RR  Quote
09-20-2013 02:02 AM  4 years agoPost 13
wc_wickedclown (RIP)

rrProfessor

long beach calif

My Posts: All  Forum  Topic

trim optimizer and tail optimizer
do i uncheck them both after i'm done

Insha Allah made in america

PM  EMAIL  HOMEPAGE  GALLERY  Attn:RR  Quote
09-20-2013 02:46 AM  4 years agoPost 14
Kauaiguy

rrNovice

Hawaii

My Posts: All  Forum  Topic

Uncheck them as they will keep changing parameters and make each flight different.

I'd rather be flying!

PM  EMAIL  Attn:RR  Quote
09-20-2013 03:18 PM  4 years agoPost 15
wc_wickedclown (RIP)

rrProfessor

long beach calif

My Posts: All  Forum  Topic

c Review - Newest First Need to quote? Mouse select. Mouse drag up. Click quote.
Kauaiguy
Uncheck them as they will keep changing parameters and make each flight different.
thank you

Insha Allah made in america

PM  EMAIL  HOMEPAGE  GALLERY  Attn:RR  Quote
WATCH
 1 page 1224 views POST REPLY
HomeAircraftHelicopterFlybarless Rotor Head SystemsV-Bar › vbar tail gain issue help
 Print TOPIC  Make Suggestion 

 5  Topic Subscribe

Sunday, August 19 - 5:16 am - Copyright © 2000-2018 RunRyder   EMAILEnable Cookies

Login Here
 New Subscriptions 
 Buddies Online