RunRyder RC
WATCH
 1 page 4370 views POST REPLY
HomeAircraftMulti-Rotor
e-
Multi-Rotor Main Discussion
DJI News  New Firmware for DJI Zenmuse H3-2D GoPro Gimbal!
07-12-2013 04:48 PM  5 years agoPost 1
DJI Innovations

rrApprentice

Shenzhen, China

My Posts: All  Forum  Topic

DJI released the Firmware 1.02, Assistant Software 1.02 & User Manual 1.06 for Zenmuse H3-2D!

What is new?
1.Change the pitch control channel of WKM to X3 Channel;
2. Add Hibernation Mode for gimbal protection. In the condition that the camera is not mounted on the gimbal the gimbal will enter into Hibernation Mode, in which the gimbal is out of control from Transmitter. You must mount the camera correctly and power cycle the system to activate the gimbal;
3. Add Hibernation Mode for gimbal protection. When certain external forces act on the gimbal, it will enter Hibernation Mode too. You must take notes to avoid too large forces affecting the normal working status of gimbal and power cycle the system to activate the gimbal.

What's Changed for Assistant software?
1. Change the pitch control channel of WKM to X3 Channel.

Changes for User Manual?
1. Change the pitch control channel of WKM to X3 Channel.
2. Add description of Hibernation Mode for gimbal protection.

*Please upgrade the autopilot system(Naza-M/Naza-M V2/WooKong-M) to the latest Firmware. Click http://www.dji-innovations.com/dji-...-1-06-released/ for More Informations!

PM  EMAIL  Attn:RR  Quote
07-15-2013 08:30 PM  5 years agoPost 2
Sidneyw

rrApprentice

Huntersville, NC

My Posts: All  Forum  Topic

FW V1.02 has tilt issue .... use V 1.04 released today.

PM  EMAIL  GALLERY  Attn:RR  Quote
07-16-2013 04:41 PM  5 years agoPost 3
Sidneyw

rrApprentice

Huntersville, NC

My Posts: All  Forum  Topic

Here is a short vid .. tilt works finally.

Watch at YouTube

PM  EMAIL  GALLERY  Attn:RR  Quote
07-16-2013 05:21 PM  5 years agoPost 4
Life_Nerd

rrVeteran

USA

My Posts: All  Forum  Topic

@Sidneyw

Very cool!

PM  EMAIL  GALLERY  Attn:RR  Quote
07-16-2013 05:52 PM  5 years agoPost 5
adarsh_007

rrApprentice

Bangalore, India

My Posts: All  Forum  Topic

@sydney & dji : any idea when the three axis gopro will be launched?
Also there's a buzz about DD mount for a 5d launching, when will this be out for retail?

Straight & Level Flying Prohibited

PM  EMAIL  GALLERY  Attn:RR  Quote
07-18-2013 04:58 AM  5 years agoPost 6
Sidneyw

rrApprentice

Huntersville, NC

My Posts: All  Forum  Topic

I can't be sure; but I know the 3-axis is in the plan. GH3 should be in a few weeks; 5D can be in a couple months or sooner. But, don't mark my words.

PM  EMAIL  GALLERY  Attn:RR  Quote
07-21-2013 04:20 AM  5 years agoPost 7
Tahoe Ed

rrNovice

Lake Tahoe, NV USA

My Posts: All  Forum  Topic

I finished my F450 build with the H3-2D, iOSD and Video Down LInk. There is a lot of electronics on a small platform but it balances well. I am planning on running 4S with the DJI 10x3.8 props. I got a set of the DJI landing gear. They attach with two screws through the bottom plate and into the arms that are longer than the normal screws. They will also work on the F550 and have additional holes to mount at an angle. My only concern is in tall grass, they may not be tall enough to allow the H3-2D to clear. I will find out tomorrow. I have a F550 that has no gimbal but taller landing gear. I will try that next week.

PM  EMAIL  Attn:RR  Quote
09-01-2013 02:26 AM  5 years agoPost 8
Sidneyw

rrApprentice

Huntersville, NC

My Posts: All  Forum  Topic

DJI at IRCHA 2013 video ... Derrick did an excellent work in editing.

Watch at YouTube

PM  EMAIL  GALLERY  Attn:RR  Quote
10-14-2013 06:37 AM  5 years agoPost 9
indydrt

rrNovice

FL.

My Posts: All  Forum  Topic

Zenuse and canon d5
What's story. When's the cannon d5 gimble being released ?

PM  EMAIL  GALLERY  Attn:RR  Quote
01-13-2014 04:14 AM  4 years agoPost 10
DJI Innovations

rrApprentice

Shenzhen, China

My Posts: All  Forum  Topic

DJI is going to release an FPV Hub Kit for Phantom 2!
PHANTOM 2 FPV HUB kit contains only cables and the FPV HUB to make connections convenient, easy and thus removing the need to do soldering when connecting them to a iOSD mini,iOSD Mark II or a DJI specified wireless video transmission module AVL58. Only 4 cables require soldering if users opt to use a wireless video transmission that’s not specified by DJI.

Connections
Choose devices collocation used with FPV-HUB according to required functions.

For wireless video transmission, the ALV58 is recommended for easy connection, using a HUB-AVL58 cable.

Collocation 1: Wireless video transmission module connected

1)Stop the Micro switch at VID position if only wireless video transmission module is connected to the FPV HUB.
2)Wireless video transmission module is an alternative to AVL58 or others unspecified. If using the AVL58, connect it to the FPV HUB via HUB-AVL58 cable. If using other wireless video transmission module, connect it to the FPV HUB via HUB-VTX cable according to pins description of the HUB-VTX cable.

Collocation 2&3: iOSD mini/iOSD MARK II and video transmission module connected

1)It’s alternative to use iOSD mini or iOSD Mark II.
2)Stop the Micro switch at OSD position when iOSD is connected to the FPV HUB.
3)Please refer to Collocation1 to connect the wireless video transmission module.

Notes:
(1)If using the FPV HUB, the original 4-Pin cable and video cable on PHANTOM 2 will be spared, please remove and clear them out. Make sure the video cable is totally cleared without any copper wire left to prevent short circuit damage.
(2)All connection operations should be conducted when the intelligent battery is powered off.
(3)Check whether pins of the connectors on the FPV HUB are straight and in good condition before connecting. Pls plug and unplug the connector carefully to avoid damage or short circuit.
(4)It’s not recommended to install the FPV HUB and extended devices inside the PHANTOM 2 aircraft.
(5)Make sure to install the AVL58 away from the compass to avoid interference.
(6)FPV HUB is non water-proof, if it is wet, please wash it with alcoholic cleanser and dry it before use. Otherwise components may be damaged cause of electrochemical corrosion.
(7)Do not leak any metal, conductive objects into the connector pins of FPV HUB to prevent short circuit damage.
(8)It’s not recommended to use cables not in the kit to connect devices to avoid unexpected damage.
(9)Make sure the connection is correct when using non-DJI recommended wireless video transmission module.

Tips:
(1)FPV HUB has a resettable fuse for over circuit precaution. The fuse will automatically open if the working current of power consuming devices (except DJI Zenmuse series) goes over 2A or if VCC and GND short circuited to prevent damage. After the short circuit trouble issued or the over current load is removed, turn off the power of the intelligent battery, the fuse will recover after 10secs.
(2)A component will be damaged if PHANTOM 2 has been short circuit once. In this condition, users still can use the FPV HUB and make the PHANTOM 2 work well again, ignoring the damaged component.

PM  EMAIL  Attn:RR  Quote
01-13-2014 04:54 AM  4 years agoPost 11
DJI Innovations

rrApprentice

Shenzhen, China

My Posts: All  Forum  Topic

DJI released new firmware for Zenmuse H3-2D!
What’s new?

Firmware

Optimized user experience when using the PHANTOM 2 remote controller for Zenmuse H3-2D pitch control.

Important notes for PHANTOM 2 users:

For users of the PHANTOM 2 with Zenmuse H3-2D, one must adhere to following steps to upgrade the remote controller firmware.

1)Use the PHANTOM RC Assistant software to upgrade the remote controller firmware to V1.0.1.11.
2)Calibrate the sticks and X1 channel of the remote controller using the PHANTOM RC Assistant software.
3)Use the PHANTOM 2 Assistant software to upgrade the Gimbal IMU firmware to V1.8 via Upgrade page.
4)After the upgrade is completed, calibrate the X1 channel of the main controller using the PHANTOM 2 Assistant software to ensure compatibility of PHANTOM 2 and the Zenmuse H3-2D.

Please click here for more information.

PM  EMAIL  Attn:RR  Quote
01-24-2014 12:10 PM  4 years agoPost 12
DJI Innovations

rrApprentice

Shenzhen, China

My Posts: All  Forum  Topic

DJI released the FPV HUB, camera mounting bracket and prop guard for Phantom 2!
PHANTOM 2 FPV HUB

In the kit:

FPV HUB, cables and instructions

Function:

Customized ports and cables for iOSD mini, iOSD Mark II or AVL58.

Feature:

FPV HUB’s integrated iOSD mini,iOSD Mark II or AVL58 ports,
connecting directly to the PHANTOM 2 central board and built-in
main controller through an 8-Pin cable. This simplifies connecting
these items and eliminates the need for soldering.

PHANTOM 2 Camera Mounting Bracket

In the kit:

Camera mounting bracket and screws

Function:

Attachment for GoPro cameras and others.

Feature:

Gimbal free camera attachment for GoPro and similar cameras.

PHANTOM 2 Prop Guard

In the kit:

4 prop guards and instructions

Function:

Fitted under the rotors to prevent damage to rotors or surroundings.

Feature:

Easy to attach, lightweight, safe and reliable.

Specifications:

Weight (Single): 21g
Angle: 150.0°
Radius: 128.25mm
Whole Size with Four Prop Guards: 613mm

Important Notes:

Make sure the PHANTOM 2 weighs no more than 1350g after
mounting prop guards. Any extra weight will compromise flight
capabilities causing a safety risk. The total weight of a PHANTOM 2
with H3-2D gimbal, iOSD and wireless video transmitter will be over
1300g, prop guards are not recommended for similarly equipped
PHANTOM 2s.

Please click here for more information.

PM  EMAIL  Attn:RR  Quote
02-21-2014 01:51 PM  4 years agoPost 13
DJI Innovations

rrApprentice

Shenzhen, China

My Posts: All  Forum  Topic

DJI released the car charger for Phantom 2!
DJI Phantom 2 car charger has been released to provide outdoor charging solutions for the Phantom 2 battery.

Phantom 2 Car Charger:

In the kit:
Car charger and instructions

Function:

Used to charge the Phantom 2 in-car or through 3S-6S Li-Po batteries.

Feature:

Convenient, practical outdoor charging solutions for the Phantom 2 battery.

Note:

FPV Hub Kit Instruction V1.1 has added description of using FPV Hub to connect the H3-2D gimbal, GCU and other devices on non-Phantom 2 flight platforms.

Please click here for more information.

PM  EMAIL  Attn:RR  Quote
WATCH
 1 page 4370 views POST REPLY
HomeAircraftMulti-Rotor
e-
Multi-Rotor Main Discussion
DJI News  New Firmware for DJI Zenmuse H3-2D GoPro Gimbal!
 Print TOPIC  Make Suggestion 

 5  Topic Subscribe

Wednesday, November 14 - 9:00 am - Copyright © 2000-2018 RunRyder   EMAILEnable Cookies

The RC discussion world needs to consolidate. RR is now one choice for that. Its software is cutting edge. It hosts on-topic advertising. Help RR increase traffic buy making suggestions, posting in RR's new areas (sites) and by spreading the word.

The RunRyder Difference

• Category system to allow Rep/Vendor postings.
• Classifieds with sold (hidden) category.
• Classifieds with separate view new.
• Answer PMs offsite via email reply.
• Member gallery photos with advanced scripting.
• Gallery photo viewer integrated into postings.
• Highly refined search with advanced back end.
• Hosts its own high end fast response servers.
• Hosts thousands of HD event coverage videos.
• Rewrote entire code base with latest technology.
• No off-topic (annoying) click bait advertising.
Login Here
 New Subscriptions 
 Buddies Online