RunRyder RC
WATCH
 1 page 943 views POST REPLY
HomeAircraftHelicopter
e-
SAB
Goblin 500 › goblin 500 loss power
06-16-2013 10:10 PM  5 years agoPost 1
nyrican

rrNovice

chesapeake, VA

My Posts: All  Forum  Topic

Ok guys i am wanting to know any information to this problem i have. First tell you what happen i am flying my goblin 500 with quatom motor and talon esc. i have like 25 flight with this hell. today i am hover did flips and pirettes and everything went good. well i went to do a loop and when i was half to my loop i loss power and it my first auto from the height i flipped it over and landed perfect to the ground was actually stoked i did. I thought i might have hit throtte hold or something because once on ground i was able to start it up again with no problem. well i went to do the loop again and same result auto it again this time to the bushes but was smooth in and no damage. This time i took blades off and ran the engne up in idle up fully collective both positive and negative i hit wire and put it over my head no lost of power. So now i am thinking it could be one way bearing(yesterday i had the bearing upside downand seized up) took it apart and ca the bearing because the outside of the bearing was moving. took it up again and same thing loss power half way in loop auto it perfect again. So i am think the internal of one way bear is mess up what do you guys think. after all that i say was successful day i auto three times why i was inverted in a loop.

Team Heliproz, Team Ikon

PM  EMAIL  GALLERY  Attn:RR  Quote
06-16-2013 11:15 PM  5 years agoPost 2
wrongler

rrProfessor

Brewerton, New York

My Posts: All  Forum  Topic

My guess, Check all wire connections!

Bill Whittaker

PM  EMAIL  GALLERY  Attn:RR  Quote
06-17-2013 01:05 AM  5 years agoPost 3
Pirofreak

rrNovice

St Louis

My Posts: All  Forum  Topic

Over drawing amp.
You need to go into ESC set up menu and change the ESC cut off setting. Your ESC probably is set to hard cutoff and sensitivity is set to sensitive setting for cut off setting. Change that to soft cutoff which will lower the throttle output to let you know you are over drawing amperage without make you auto. Also change the sensitivity to insensitive as long as you have the c rating on lipo that can handle it. Hope this will help.

PM  EMAIL  Attn:RR  Quote
06-17-2013 03:46 AM  5 years agoPost 4
nyrican

rrNovice

chesapeake, VA

My Posts: All  Forum  Topic

the day before i seized the motor because one way was backwards but put it back and engine still running good until i do loop i read the xt60 connectors out and i am getting a big difference of resistance to the solder point to actual pin if i move it too could that be a issue

Team Heliproz, Team Ikon

PM  EMAIL  GALLERY  Attn:RR  Quote
WATCH
 1 page 943 views POST REPLY
HomeAircraftHelicopter
e-
SAB
Goblin 500 › goblin 500 loss power
 Print TOPIC  Make Suggestion 

 2  Topic Subscribe

Tuesday, November 20 - 7:41 am - Copyright © 2000-2018 RunRyder   EMAILEnable Cookies

The RC discussion world needs to consolidate. RR is now one choice for that. Its software is cutting edge. It hosts on-topic advertising. Help RR increase traffic buy making suggestions, posting in RR's new areas (sites) and by spreading the word.

The RunRyder Difference

• Category system to allow Rep/Vendor postings.
• Classifieds with sold (hidden) category.
• Classifieds with separate view new.
• Answer PMs offsite via email reply.
• Member gallery photos with advanced scripting.
• Gallery photo viewer integrated into postings.
• Highly refined search with advanced back end.
• Hosts its own high end fast response servers.
• Hosts thousands of HD event coverage videos.
• Rewrote entire code base with latest technology.
• No off-topic (annoying) click bait advertising.
Login Here
 New Subscriptions 
 Buddies Online