RunRyder RC
WATCH
 1 page 2028 views POST REPLY
HomeAircraftHelicopterAlignT-REX 600N › 3GX Governor and 9503
05-28-2013 01:57 AM  5 years agoPost 1
trappg

rrNovice

Concord, NC

My Posts: All  Forum  Topic

New to the world of helicopters and would like some assistance with my Trex 600N gov setup. I have the Align 55 motor, 3GX and I have just installed my governor sensor to pick up the stock fan magnets. Now what? My TX is a JR9503. I have read where the default is CH5 for the gov but don't have a lot of knowledge of what to do next. I have been thru the 3GX setup in getting a green gov light. Assistance is appreciated since Align is pretty cryptic with things like this.

PM  EMAIL  GALLERY  Attn:RR  Quote
05-28-2013 02:51 AM  5 years agoPost 2
dkshema

rrMaster

Cedar Rapids, IA

My Posts: All  Forum  Topic

You're mostly there.

If you are using Spektrum satellite receivers as your 3GX receivers, you are correct in that channel 5 is the one that is to be used for controlling the governor.

Back to your 9503. In the system setup menu, open up the Device Select menu and enable the GOVERNOR as shown here:

You will now have a new selection in your menu called "GOVERNOR", and the Flight Mode Switch will control the RPM settings in this menu.

When you go to the GOVERNOR menu, you will see place holders for RPM setting values for the Governor in Normal mode, ST-1 mode, ST-2 mode, and HOLD mode.

These values are what controls the governed RPM for the selected mode (again, controlled through the Flight Mode Switch).

Now that you have the Governor menu operating out of channel 5 of your TX, you'll want to go to the 3GX menu, to this page:

Enter the main gear/pinion gear ratio in the top box. (If you don't know the gear ratio, either look it up in your heli's manual, or count the number of teeth on the big main gear, and count the number of teeth on the pinion gear. Divide the number of teeth on the main gear by the number of teeth on the pinion...that is the gear ratio.

(Example: Main gear has 100 teeth, pinion has 10 teeth. Ratio is 100 / 10 = 10).

With the gear ratio entered in the 3GX menu box, select the flight mode for which you wish to set an RPM, then use the 9503 roller wheel to increase the number while watching the resulting RPM on the 3GX display page.

Set the desired RPM for each of the flight modes. You'll see in my pictures above that I have the Governor disabled in Normal and Hold mode. ST-1 and ST-2 have the values I ended up with, when setting desired RPMs for my Gaui NX4.

-----

Make sure that you have gone through the calibration sequence of your X9503/3GX combo as described in the 3GX menu stuff -- Use a linear 0 to 100% throttle curve when you do this, and your pitch curve for - full pitch to + full pitch (probably your ST-2 setting) when you do this.

Don't forget to put those back where they should be, before flying.

-----
Dave

* Making the World Better -- One Helicopter at a time! *

Team Heliproz

PM  EMAIL  GALLERY  Attn:RR  Quote
05-30-2013 01:13 AM  5 years agoPost 3
trappg

rrNovice

Concord, NC

My Posts: All  Forum  Topic

AWESOME! Thanks dkshema! I got all that done now just need to get out to fly it and determine % values. Is there a way (on the workbench) to tell if the gov sensor is working properly? Ie: maybe a flashing light when signal is detected?

PM  EMAIL  GALLERY  Attn:RR  Quote
05-30-2013 02:17 PM  5 years agoPost 4
dkshema

rrMaster

Cedar Rapids, IA

My Posts: All  Forum  Topic

As I recall, the light blinks as the magnet passes by. I'd double check that, but the one installation I have where I'm using the internal governor spit out its magnets yesterday. I need to check today if the sensor survived.

-----
Dave

* Making the World Better -- One Helicopter at a time! *

Team Heliproz

PM  EMAIL  GALLERY  Attn:RR  Quote
06-06-2013 01:52 PM  5 years agoPost 5
trappg

rrNovice

Concord, NC

My Posts: All  Forum  Topic

Thx again for your help. I have flown and adjusted the governor to my liking. Very clear and concise instructions. Sorry to hear abt your troubles. Hope things weren't torn up too badly.

PM  EMAIL  GALLERY  Attn:RR  Quote
WATCH
 1 page 2028 views POST REPLY
HomeAircraftHelicopterAlignT-REX 600N › 3GX Governor and 9503
 Print TOPIC  Make Suggestion 

 2  Topic Subscribe

Sunday, August 19 - 1:27 am - Copyright © 2000-2018 RunRyder   EMAILEnable Cookies

Login Here
 New Subscriptions 
 Buddies Online