RunRyder RC
WATCH
 1 page 740 views TOPIC CLOSED
Home✈️Aircraft🚁HelicopterBeginners Corner › Need help!
05-10-2013 11:42 PM  6 years ago
Topic Vote0Post 1
tgalo

rrVeteran

USA

MyPosts All Forum Topic
Need help!
I have a new DX7s and a new TM1000 telemetry module. Bind the system and everything works fine. Shut it down and restart and the light on the TM1000 blinks like its in bind mode but I still have control over everything else. Swapped the TM1000 and same thing. Any help or thoughts?
Gravity's a bitch ant it?
SHARE  PM  EMAIL  GALLERY  Attn:RR
05-10-2013 11:46 PM  6 years ago
wrongler

rrProfessor

Brewerton, New York

MyPosts All Forum Topic
Did you power off the heli and the TX? If you just turn off the TX and back on the RX lite will blink.Bill Whittaker
SHARE  PM  EMAIL  GALLERY  Attn:RR
05-10-2013 11:54 PM  6 years ago
RCHSF

rrKey Veteran

NC

MyPosts All Forum Topic
Edit....
SHARE  PM  EMAIL  Attn:RR
05-11-2013 12:23 AM  6 years ago
tgalo

rrVeteran

USA

MyPosts All Forum Topic
No I power of th rx first then the tx. When I plug in the tm1000 to the ar7200bx, the manual says press and hold the button on the tm1000 and all connected should blink and the do. It connects fine right after I bind it. It's when I power down and try to power it back up.Gravity's a bitch ant it?
SHARE  PM  EMAIL  GALLERY  Attn:RR
05-11-2013 12:26 AM  6 years ago
RCHSF

rrKey Veteran

NC

MyPosts All Forum Topic
You do have the data cable from the tm1000 data port plugged into the ar7200bx right?

Yeah the main rx, or in your case the ar7200bx will be bound first to your TX. Then you connect the tm1000 to the ar7200bx. Then press the tm1000 button while powering on your heli's power. All lights should be flashing. Then put tx into bind mode.

So your actually binding twice. If your doing it from scratch.
SHARE  PM  EMAIL  Attn:RR
05-11-2013 12:34 AM  6 years ago
tgalo

rrVeteran

USA

MyPosts All Forum Topic
nop still does the same thing, I'm lostGravity's a bitch ant it?
SHARE  PM  EMAIL  GALLERY  Attn:RR
05-11-2013 12:43 AM  6 years ago
tgalo

rrVeteran

USA

MyPosts All Forum Topic
Yes, I do have it plugged in. I'll try it that you say when I get homeGravity's a bitch ant it?
SHARE  PM  EMAIL  GALLERY  Attn:RR
05-11-2013 11:43 PM  6 years ago
tgalo

rrVeteran

USA

MyPosts All Forum Topic
Just thought I post if someone runs into this. On the phone with the Horizon guys 3 times. here was the solution. He said to bind the system and then power off the heli but leave the tx on. Then remove the signal wire from the data lead that goes from the tm1000 to the rx. They said that is what was causing the module to go back into bind mode. Then power on the heli and it should stay bound. So far so goodGravity's a bitch ant it?
SHARE  PM  EMAIL  GALLERY  Attn:RR
WATCH
 1 page 740 views TOPIC CLOSED
Home✈️Aircraft🚁HelicopterBeginners Corner › Need help!
 Print TOPIC  Make Suggestion 

 2  Topic Subscribe

Wednesday, February 26 - 2:06 pm - Copyright © 2000-2020 RunRyder   EMAILEnable Cookies

Login Here
 New Subscriptions 
 Buddies Online