RunRyder RC
WATCH
 1 page 961 views POST REPLY
HomeRC & Power✈️Aircraft🚁HelicopterFlybarless Rotor Head SystemsBeastX › AR7200bx travel limits (leveling the swash)
04-07-2013 02:12 PM  6 years ago
Topic Vote0Post 1
Blackhawk6

rrVeteran

Trenton, Mi

MyPosts All Forum Topic
AR7200bx travel limits (leveling the swash)
Hey all!

I've noticed in the past couple flights after setting up the unit that during piro's the heli will drift a little. This tells me the swash isn't level...

So, I put in on the bench to check everything. In menu "G" (with a leveling tool installed) the swash is perfectly level. Not so true when I add collective tho. I can see that one servo lacks a little behind during positive collective causing the swash to be off.

I couldn't figure out how to adjust this? Where in the setup can I adjust the travel limits to correct this?

Thanks!
Jason
SHARE  PM  EMAIL  GALLERY  Attn:RR  Quote
04-07-2013 04:15 PM  6 years ago
wifeorheli

rrElite Veteran

reno, nevada usa

MyPosts All Forum Topic
Mine does the same at full collective my swash tilts
This normal and shouldnt be noticed in flight as the unit will correct. Do some punch outs and observe if the heli goes straight up. Also make sure your cg is spot on. Remember fbl is not auto pilot it will not piro handsmoff forever. Let us know...
Novarossi Motors U.S.A
www.PLanethobby.com
Team GrandRc.com
Team Byron Fuels
ZRC U.S.A. "PushGlo, SwitchGlo"
SHARE  PM  EMAIL  HOMEPAGE  GALLERY  Attn:RR  Quote
04-07-2013 05:24 PM  6 years ago
Blackhawk6

rrVeteran

Trenton, Mi

MyPosts All Forum Topic
Mine doesn't tilt at full collective. It's just that one servo is a little lower between +2 and +8 or so. I've done climb outs and yes, it stays heading straight up. I know that no heli will piro "hands off" but it seems mine is squirley from the start no matter how fast it spins.

Maybe it's the CG? Ill have to check out my pack placement and make sure they're all in the same spot on the trays.

But, is there no way to adjust the travel limits of each servo with the BeastX?
SHARE  PM  EMAIL  GALLERY  Attn:RR  Quote
04-08-2013 08:46 AM  6 years ago
meatbomber

rrApprentice

Klatovy, Czech Republic

MyPosts All Forum Topic
No unfortunately it doesn't.
SHARE  PM  EMAIL  HOMEPAGE  GALLERY  Attn:RR  Quote
04-09-2013 08:35 AM  6 years ago
dj80550

rrVeteran

Texas

MyPosts All Forum Topic
But, is there no way to adjust the travel limits of each servo with the BeastX?
I am dealing with the same issue, uneven elevator at full pitch. There are a few tradeoffs you can do, swap servo horns, try different ball links, or parameter A at the field, once you definitely know with no wind there is a drift.

The beastx admin. support wrote this about an upcoming update:

"Anyhow, with next version of the Microsettings PC software you will be able to adjust servo throws separately by using the PC.
Software should be finished within next two months, at least that's the plan.."
AMA# 1078375
SHARE  PM  EMAIL  Attn:RR  Quote
WATCH
 1 page 961 views POST REPLY
HomeRC & Power✈️Aircraft🚁HelicopterFlybarless Rotor Head SystemsBeastX › AR7200bx travel limits (leveling the swash)
 Print TOPIC  Make Suggestion 

 2  Topic Subscribe

Tuesday, July 23 - 8:43 pm - Copyright © 2000-2019 RunRyder   EMAILEnable Cookies

Login Here
 New Subscriptions 
 Buddies Online