RunRyder RC
WATCH
 1 page 641 views POST REPLY
Home✈️Aircraft🚁HelicopterGasser Model RC HelicoptersOther › G231 Best way to take off Flywheel?
01-05-2013 07:43 PM  7 years ago
Topic Vote0Post 1
jbdww

rrElite Veteran

Round Rock, Texas

MyPosts All Forum Topic
G231 Best way to take off Flywheel?
I just got my conversion in to convert my G231 from magneto to electronic ignition. What is the best way to pull the flywheel?
Thanks
Joe
Skids Up
http://www.jbdww.com
http://twitter.com/jbdww/
SHARE  PM  EMAIL  HOMEPAGE  GALLERY  Attn:RR  Quote
01-05-2013 09:30 PM  7 years ago
jgoodsell

rrApprentice

Sherbrooke, Qc, Canada

MyPosts All Forum Topic
I made myself a puller using a U shaped aluminium rail with 3 bolts

The 2 outer ones line up with the 2 holes in the flywheel, and are of the same thread and size as the holes. The center bolt is smaller and rests on the crank shaft. You can use a nut on the center bolt to adjust the length.

Place this assembly over the flywheel an equally tighten the two outer bolts in a way that the center bolt rests on the crankshaft.

gradually apply more tension with the outer bolts. when you feel there is lots of tension a small tap on the crank will release it.

I hope you see the picture because this is hard to illustrate in writing.

Jeffrey
It seams that Gravity is worst around here !
SHARE  PM  EMAIL  HOMEPAGE  GALLERY  Attn:RR  Quote
01-05-2013 11:40 PM  7 years ago
Carey Shurley

rrElite Veteran

Orlando, FL - USA

MyPosts All Forum Topic
the absolute EASIEST way is with this tool:

Flywheel puller tool

it is of course not the ONLY way or the cheapest way
Proprietor - Gas Powered Helicopters
SHARE  PM  EMAIL  GALLERY  Attn:RR  Quote
01-06-2013 02:25 AM  7 years ago
fastflyer20

rrKey Veteran

N. Tonawanda, NY

MyPosts All Forum Topic
If you want something quick, this boat post shows a simple one you can make.

http://www.modelgasboats.com/Zenoah_Teardown/
SHARE  PM  EMAIL  GALLERY  Attn:RR  Quote
01-06-2013 02:36 AM  7 years ago
jbdww

rrElite Veteran

Round Rock, Texas

MyPosts All Forum Topic
Thank you guys so much. I have some spare alumine, so I will try to make a puller.Skids Up
http://www.jbdww.com
http://twitter.com/jbdww/
SHARE  PM  EMAIL  HOMEPAGE  GALLERY  Attn:RR  Quote
01-07-2013 04:19 AM  7 years ago
GREYEAGLE

rrElite Veteran

Flat Land's

MyPosts All Forum Topic
j goodsell has it exactly correct ;

I had mine in the photo gallery but it didn't make it in the new file transfer's of photo's

- it's a piece of cake - I use aluminum angle iron I had laying around

It's really easy - after you get just a whisper of tension on it then warm the flywheel up a bit with you heat gun - Simple

Just don't grab it bare handed it will be warm
greyeagle
SHARE  PM  EMAIL  GALLERY  Attn:RR  Quote
01-07-2013 11:40 AM  7 years ago
Rototerrier

rrVeteran

Fayetteville, GA - USA

MyPosts All Forum Topic
I use this one for $22

http://www.davesmotors.com/s.nl/c.8...it.A/id.4093/.f
Gassers Rule, Nitros Drool, Electrics...uhhh...Joule?
SHARE  PM  EMAIL  GALLERY  Attn:RR  Quote
01-07-2013 03:57 PM  7 years ago
jgoodsell

rrApprentice

Sherbrooke, Qc, Canada

MyPosts All Forum Topic
looks like mine but WAY nicer

Jeffrey
It seams that Gravity is worst around here !
SHARE  PM  EMAIL  HOMEPAGE  GALLERY  Attn:RR  Quote
WATCH
 1 page 641 views POST REPLY
Home✈️Aircraft🚁HelicopterGasser Model RC HelicoptersOther › G231 Best way to take off Flywheel?
 Print TOPIC  Make Suggestion 

 3  Topic Subscribe

Sunday, July 5 - 10:24 am - Copyright © 2000-2020 RunRyder   EMAILEnable Cookies

Login Here
 New Subscriptions 
 Buddies Online