RunRyder RC
 2  Topic Subscribe
WATCH
 1 page 668 views POST REPLY
HomeAircraftHelicopterAlignT-REX 600N › cyclic servo's not working
10-14-2012 08:41 PM  5 years agoPost 1
gingus1

rrApprentice

Lafayette,La.

My Posts: All  Forum  Topic

Put my 600n le fbl in a few weeks back and now trying to get it back up in the air, my problem is when i turn tx. and rx on every thing arms and the 3g unit goes through it's routine with swash doing it's thing but after that i notice the align gov. doesn't arm and can't get any respond with cyclic servo's. The rx light's are solid not blinking so i'm assuming it is binding. Tried changing models on the tx and coming back to it and got it working once by doing so but can't seem to get it to do it again. It's got me baffle and don't know what to try next to get it going again.
Any input would be appreciated. thanks.

You Da-Man

PM  EMAIL  GALLERY  Attn:RR  Quote
10-14-2012 09:04 PM  5 years agoPost 2
BladeStrikes

rrElite Veteran

Shelby TWP,Mi

My Posts: All  Forum  Topic

Try rebinding..Had that happen to me once and all was good after rebinding.

PM  EMAIL  GALLERY  Attn:RR  Quote
10-14-2012 09:11 PM  5 years agoPost 3
gingus1

rrApprentice

Lafayette,La.

My Posts: All  Forum  Topic

ill try that thx.

You Da-Man

PM  EMAIL  GALLERY  Attn:RR  Quote
10-15-2012 01:11 AM  5 years agoPost 4
gingus1

rrApprentice

Lafayette,La.

My Posts: All  Forum  Topic

i rebinded it and it worked,but if i turn just the rx off than back on everything will arm again. When i turn the rx and tx off than back on again sometimes i need to do it several times before the gov. and cyclic servo's will arm. I'm just wondering if it could be a tx. problem.

You Da-Man

PM  EMAIL  GALLERY  Attn:RR  Quote
10-15-2012 02:06 AM  5 years agoPost 5
Zaneman007

rrElite Veteran

Texas - USA

My Posts: All  Forum  Topic

Antenna placement?
With the spectrum sats, only one wire is active. It needs to be away from the carbon fiber and any noise, such as wires.

Although 95% of the folks out there put them anywhere without issue, 5% have issues. If only one of the sats bound, before FBL came along you might have notice a drift in the tail. With FBL you notice the the FBL isn't working properly.

The solution move the sats away from the carbon fiber, and have them at 90 degrees for optimum polarization.

Old Guys Rule!

PM  EMAIL  GALLERY  Attn:RR  Quote
10-15-2012 02:38 AM  5 years agoPost 6
gingus1

rrApprentice

Lafayette,La.

My Posts: All  Forum  Topic

I have the sat. as far away as it can be from the cf. It's on the plastic nose on the very front. Can't be any farther away than that. never had the problem before that's what got me thinking it could be the radio. It's never been droped but it is at lease 5 to 7 years old.

You Da-Man

PM  EMAIL  GALLERY  Attn:RR  Quote
10-15-2012 10:40 PM  5 years agoPost 7
BladeStrikes

rrElite Veteran

Shelby TWP,Mi

My Posts: All  Forum  Topic

gingus1
i rebinded it and it worked,but if i turn just the rx off than back on everything will arm again. When i turn the rx and tx off than back on again sometimes i need to do it several times before the gov. and cyclic servo's will arm. I'm just wondering if it could be a tx. problem.
I would send the TX and RX in..If its never did that untill the crash,something in the RX could of come loose.Do you have another RX sitting around?If so,put it in and see what happens..

PM  EMAIL  GALLERY  Attn:RR  Quote
10-16-2012 12:06 AM  5 years agoPost 8
gingus1

rrApprentice

Lafayette,La.

My Posts: All  Forum  Topic

I would send the TX and RX in..If its never did that untill the crash,something in the RX could of come loose.Do you have another RX sitting around?If so,put it in and see what happens..
thx. for the advice but i think my rx and tx is to old to send in i think i'm better off getting new stuff. I did manage it get it to arm every time i turn it on now,i played with the antenna on the tx and it seems to be working so for so i'm going to take a change and put it in the air and see what happens. Thanks for your input and everyone else.

You Da-Man

PM  EMAIL  GALLERY  Attn:RR  Quote
10-16-2012 02:38 AM  5 years agoPost 9
HiroboFreak

rrVeteran

Central Coast, NSW, Australia

My Posts: All  Forum  Topic

Do a range test on the ground before putting it in the air!

T-rex700n VBar 5.3 Pro | T-rex700e DFC VBar 5.3 Pro | JR DSX9
Team RCBits | Team Lynx

PM  EMAIL  HOMEPAGE  GALLERY  Attn:RR  Quote
10-16-2012 02:41 AM  5 years agoPost 10
gingus1

rrApprentice

Lafayette,La.

My Posts: All  Forum  Topic

Do a range test on the ground before putting it in the air!
cool.. thx.

You Da-Man

PM  EMAIL  GALLERY  Attn:RR  Quote
WATCH
 1 page 668 views POST REPLY
HomeAircraftHelicopterAlignT-REX 600N › cyclic servo's not working
 Print TOPIC  Make Suggestion 

 2  Topic Subscribe

Wednesday, June 20 - 8:42 am - Copyright © 2000-2018 RunRyder   EMAILEnable Cookies

Login Here
 New Subscriptions 
 Buddies Online