RunRyder RC
WATCH
 1 page 1732 views Post Reply
HomeRC & Power✈️Aircraft🚁HelicopterFlybarless Rotor Head SystemsBeastX › BeastX Upgrade to V3
08-05-2012 05:44 AM  9 years ago
Topic Vote0Post 1
TheWoodCrafter

rrKey Veteran

Chiloquin, OR

MyPosts All Forum Topic
BeastX Upgrade to V3
Why would I want to upgrade?

What does it do better than V2?
Thanks, TheWoodCrafter
SHARE  PM  EMAIL  GALLERY  Attn:RR  Quote
08-06-2012 03:02 AM  9 years ago
honda411

rrKey Veteran

Surprise, AZ USA

MyPosts All Forum Topic
There are a few features better. I cant remember them all and this is a free bump to get some more people to add to the list possibly. Google it to be sure.

But pitch boost is a huge plus! I love it! Tic Tocs are much easier and more aggresive.
HeliDirect Field Rep, Synergy N7 w/ OS 105, Torq Servos, Cyclone/ Rail blades
SHARE  PM  EMAIL  GALLERY  Attn:RR  Quote
08-06-2012 03:15 AM  9 years ago
Brian B.

rrApprentice

Marion, Iowa

MyPosts All Forum Topic
"New features of V3.0.0:

• reduced swash servo peak power consumption

• Throttle and Aux channel now directly "online" after power up in single line mode.

• New swashplate algorithm: again more direct and sudden reaction to cyclic commands

• At parameter menu point "F" (Revomix) now also preset values selectable. So computer is not absolutely necessary to use RevoMix function (only for fine tuning)

• Calculation of Revomix is now depending on the pitch adjustment at setup menu point "K". So it is possible to use assymetric pitch values in combination with asymmetric Revomix

• new cyclic response parameter (parameter point "G"
This allows to select a more natural - "flybarlike" control feeling. Please don't use too high expo or ATV/DR values in the beginning as this could produce a very "extreme" response of the heli. Also only increase the different stages step by step.

• New pitch boost function (parameter menu point H)

• New tail algorithm.
Perfect constant tail rate also in close proximity to the maximum rotation rate and faster response when changing rotation direction.
Therefore it is necessary to outfly the maximum possible tail gain and only increase HH-Gain (parameter menu point D) as far as necessary. Again as mentioned before don't forget to verify that the tail stick does not control the gyro into "free-wheel" mode.

• Also as already mentioned: now DSMX and DSM2 satellites supported and selectable. Again don't forget: only the type of satellite remote receiver is important for correct choice in the Microbeast.

• Trimm function at parameter menu point A slightly modified. It now works quite similar to a transmitter's trimm function by tapping the control stick to trimm the swash in small steps.

• Now compatible to our new BEASTRX receivers which support our new SRXL singleline protocol. Receivers will be fully compatible to Futaba fasst and frSky systems. Coming soon ..

• One last note: The Microsettings PC software for adjusting swashplate phasing and revomix is not compatible with this new V3 firmware. New Microsettings software is in the works and will soon be available. Thanks for your patience!
(Of course you can use the preset RevoMix values for the present!)"

Quote from Stefan.
SHARE  PM  EMAIL  GALLERY  Attn:RR  Quote
08-06-2012 03:18 AM  9 years ago
Brian B.

rrApprentice

Marion, Iowa

MyPosts All Forum Topic
"Hi,

BEASTX Software bundle is available now in the download area. This package includes Microsettings V3 software, new BEASTX updater and the driver installation for the USB2SYS interface.

Release Notes BEASTXMicroSettings 3.0.2:

- now supports MICROBEAST firmware (application) 2.x.x and 3.x.x

- scrollable GUI for better compliance with LowRes devices (netbooks, etc...)

- disconnect button, to use BEASTXUpdater and BEASTXMicroSettings together

- more settings available for MICROBEAST firmware (application) 2.x.x than in last release

Setup Menu Settings:
+ Swashplate Frequency User defined value added
+ Tail Servo CPPL User Defined value added
+ Tail Servo Frequency added
+ Swashplate-Mixer now supports mechanical mixing (MICROBEAST firmware (application) 3.x.x only)

Parameter Menu Settings:
+ Swashplate Pitching up behaviour added
+ Tail Headinglock Gain added
+ Stick Deadband added
+ Cyclic Response added (MICROBEAST firmware (application) 3.x.x only)
+ Pitch Boost added (MICROBEAST firmware (application) 3.x.x only)"
Another quote!
All the infromation you need is here:
http://www.beastx.com/forumdisplay.php?8-MICROBEAST-(English)
SHARE  PM  EMAIL  GALLERY  Attn:RR  Quote
08-06-2012 03:37 AM  9 years ago
TheWoodCrafter

rrKey Veteran

Chiloquin, OR

MyPosts All Forum Topic
Thanks guys.Thanks, TheWoodCrafter
SHARE  PM  EMAIL  GALLERY  Attn:RR  Quote
08-06-2012 05:36 AM  9 years ago
T-rexn8

rrKey Veteran

CoLoRaDo

MyPosts All Forum Topic
Can you upgrade the 7200BX?Xxtreme 800, TDR, 700E DFC, Mini Protos, T-450 DFC, Blade 130x, mcpx, nano
SHARE  PM  EMAIL  GALLERY  Attn:RR  Quote
08-06-2012 01:05 PM  9 years ago
bart2546

rrVeteran

Canal Winchester, OH - USA

MyPosts All Forum Topic
To my understanding the 7200BX is already at the latest firmware available for it and a few places online suggest to not under any circumstance use the update software from the MicroBeast website. I guess the way to stay up to date on software for that is to register it on the Spektrum community website and they will notify you or you can check in just like the DX8.Regards, Brandon Bartolomucci; Team Synergy; Team Scorpion; & Team Bavarian Demon; AMA# L939231
SHARE  PM  EMAIL  GALLERY  Attn:RR  Quote
WATCH
 1 page 1732 views Post Reply
HomeRC & Power✈️Aircraft🚁HelicopterFlybarless Rotor Head SystemsBeastX › BeastX Upgrade to V3
Print TOPIC

 1  Topic Subscribe

Wednesday, September 22 - 7:19 am - Copyright © 2000-2021 RunRyder   EMAILEnable Cookies

Login Here
 New Subscriptions 
 Buddies Online