RunRyder RC
WATCH
 1 page 773 views Post Reply
HomeRC & Power✈️Aircraft🚁Helicoptere-Electric Motors-Controllers-ESCOther › CC 160HV v2 + KDE700XF setup
04-04-2012 09:06 PM  9 years ago
Topic Vote0Post 1
Malc1

rrKey Veteran

EVESHAM,UK

MyPosts All Forum Topic
CC 160HV v2 + KDE700XF setup
Hi

I'm setting up the above combo,any chance that anyone has the correct settings in the software for Cutoffs and Motor.

Thanks
Minicopter Diabolo - Kosmik200,Pyro750-56
SpectraG + G26 3D Max
SHARE  PM  EMAIL  GALLERY  Attn:RR  Quote
04-05-2012 08:24 PM  9 years ago
zoot408

rrVeteran

MI.

MyPosts All Forum Topic
This is what I use
This is the profile i am using
taken directly from the KDE site.
#######################################################
Hex55: 85
Brake Delay: .6 sec (Delayed) (*)
Brake Ramp: Immediate (*)
Cutoff Type: Soft Cutoff
Motor Start Power: 39
Direction: Forward (*)
Brake Strength: 0
PWM Rate: 8 Khz
Cutoff Voltage: 150
Current Limiting: Disabled
Sample Frequency: 5 Sample / Sec
Power-On Beep: Disabled
Auto-Lipo Volts/Cell: 3.2 Volts/Cell (*)
Motor Timing: 5
Data Log Enabled: 239
Vehicle Type: Helicopter
Throttle Type: Governor Mode
Throttle Response: 5
Governor Gain: 15
Initial Spool-Up Rate: 5
Head Speed Change Rate: 10
Auto Rotate Enabled: True
Governor Mode Type: Fixed
Vehicle Setup - Battery Type: LiPo
Vehicle Setup - Number of Cells: 12
Vehicle Setup - Battery Voltage: 44.40
Vehicle Setup - Gear Ratio: 8.2143
Vehicle Setup - Pinion: 14
Vehicle Setup - Spur: 115
Vehicle Setup - Motor Kv: 495
Vehicle Setup - Motor Number of Poles: 8
Desired Head Speed 1: 2000
Desired Head Speed 2: 2100
Desired Head Speed 3: 2225
SHARE  PM  EMAIL  HOMEPAGE  GALLERY  Attn:RR  Quote
04-05-2012 08:43 PM  9 years ago
Malc1

rrKey Veteran

EVESHAM,UK

MyPosts All Forum Topic
Thanks for the info.

Is it right that the brake should be activated? Why?

I think also that Patrick is now recommending using a PWM rate of 12khz.
Minicopter Diabolo - Kosmik200,Pyro750-56
SpectraG + G26 3D Max
SHARE  PM  EMAIL  GALLERY  Attn:RR  Quote
04-05-2012 08:45 PM  9 years ago
zoot408

rrVeteran

MI.

MyPosts All Forum Topic
no
on the brake. My last conversation with castle, they agreed with 8pwm. Maybe try them both... and if you see flames try the other
SHARE  PM  EMAIL  HOMEPAGE  GALLERY  Attn:RR  Quote
04-05-2012 08:52 PM  9 years ago
Malc1

rrKey Veteran

EVESHAM,UK

MyPosts All Forum Topic
I just need an uneventfull test flight pleaseMinicopter Diabolo - Kosmik200,Pyro750-56
SpectraG + G26 3D Max
SHARE  PM  EMAIL  GALLERY  Attn:RR  Quote
04-05-2012 08:54 PM  9 years ago
zoot408

rrVeteran

MI.

MyPosts All Forum Topic
ahhh yes
Don't all us CC guysx2
SHARE  PM  EMAIL  HOMEPAGE  GALLERY  Attn:RR  Quote
04-05-2012 09:12 PM  9 years ago
Malc1

rrKey Veteran

EVESHAM,UK

MyPosts All Forum Topic
I must say that I am looking forward to seeing how this heli now flys.

I've been using a 700M motor and CC80Hv right from when the heli was built.
Minicopter Diabolo - Kosmik200,Pyro750-56
SpectraG + G26 3D Max
SHARE  PM  EMAIL  GALLERY  Attn:RR  Quote
04-05-2012 09:19 PM  9 years ago
zoot408

rrVeteran

MI.

MyPosts All Forum Topic
You will see
quite a difference. That motor makes for quite a kickin ride! Over the old 700m, like jumping out of your Pinto and into your Mustang! Just watch your temps, and stay away from the 4.0 beta (my experiences only.)
SHARE  PM  EMAIL  HOMEPAGE  GALLERY  Attn:RR  Quote
04-05-2012 09:32 PM  9 years ago
Malc1

rrKey Veteran

EVESHAM,UK

MyPosts All Forum Topic
I hope so.

My CC 160 is brand new as well but I have just loaded up V 4.01 before starting the programming.

I think this version is OK.

No 3D for me though only fast sports and big air.
Minicopter Diabolo - Kosmik200,Pyro750-56
SpectraG + G26 3D Max
SHARE  PM  EMAIL  GALLERY  Attn:RR  Quote
04-05-2012 09:45 PM  9 years ago
zoot408

rrVeteran

MI.

MyPosts All Forum Topic
I had better luck
with 3.27... but again, that is just my experience
SHARE  PM  EMAIL  HOMEPAGE  GALLERY  Attn:RR  Quote
WATCH
 1 page 773 views Post Reply
HomeRC & Power✈️Aircraft🚁Helicoptere-Electric Motors-Controllers-ESCOther › CC 160HV v2 + KDE700XF setup
Print TOPIC

 1  Topic Subscribe

Thursday, July 29 - 4:18 pm - Copyright © 2000-2021 RunRyder   EMAILEnable Cookies

Login Here
 New Subscriptions 
 Buddies Online