RunRyder RC
WATCH
 1 page 1392 views POST REPLY
HomeRC & Power✈️Aircraft🚁Helicoptere-Hobbywing Electric Components › HOBBYWING Flyfun 100a ESC issues
03-27-2012 04:53 AM  7 years ago
Topic Vote0Post 1
Funknrock

rrApprentice

San Marcos, CA

MyPosts All Forum Topic
HOBBYWING Flyfun 100a ESC issues
just bought and tried to hook up this new ESC. after some strugglign with getting the ESC to do anything, i was able to get it to see low setting and initialize/ spin up the motor. it will swith from normal to idle 1 but not idle 2

prob with it is that it will go into program mode. it will initialize as if it were in low position with the throttle at full. i've tried moving the travel adjust to 150% (ive tried with travel adjust in several positions) and moving the throttle trim at full. i have a linear throttle curve in normal.

i'm using a DX7 and and AR7200BX, Scorpion motor on a Gaui X5

has anyone had similar issues?
My crashes are cooler than your flying! ;^)
SHARE  PM  EMAIL  GALLERY  Attn:RR  Quote
03-28-2012 09:26 PM  7 years ago
wifeorheli

rrElite Veteran

reno, nevada usa

MyPosts All Forum Topic
I have excact same setup except the heli mine does the same thing i cant get it to do the throttle max-low just boots right up. I just fly it im getting a better one. I also have the program card too thoughNovarossi Motors U.S.A
www.PLanethobby.com
Team GrandRc.com
Team Byron Fuels
ZRC U.S.A. "PushGlo, SwitchGlo"
SHARE  PM  EMAIL  HOMEPAGE  GALLERY  Attn:RR  Quote
07-06-2012 06:20 PM  7 years ago
Funknrock

rrApprentice

San Marcos, CA

MyPosts All Forum Topic
took me a while to get back to this, but...

i only put 2 flights in with the flyfun 100a ESC. it worked well but still no 'programmed' end points.

i ended up getting a platinum pro 100a esc and the LCD program box. i've updated all the firmware, worked out all the settings with the program (similar to CC).

all this and it STILL doesn't let me set throttle end points!

i really thought this would work better once i started using my DX8, but, no change.

i set my throttle end point to 150 and although it does go into program mode, it does not set endpoints. i also only get 1 idle up speed and no change in idle 2. i've also noticed that very soft start is not all that soft.

while working on setup i used a different motor so i wouldn't have to loosen my pinion or remove the motor mount. i used the built in BEC for the initial work as well. a couple things i noticed here too...

1) it(ESC) sees low end points different with different motors.
2) it sees endpoints different with the built in BEC than by-passing with an external battery (LIFE 2cell 6 volt plugged directly into the AR7200BX)

going to test fly today. hoping it performs well.
My crashes are cooler than your flying! ;^)
SHARE  PM  EMAIL  GALLERY  Attn:RR  Quote
WATCH
 1 page 1392 views POST REPLY
HomeRC & Power✈️Aircraft🚁Helicoptere-Hobbywing Electric Components › HOBBYWING Flyfun 100a ESC issues
 Print TOPIC  Make Suggestion 

 1  Topic Subscribe

Sunday, August 18 - 12:03 pm - Copyright © 2000-2019 RunRyder   EMAILEnable Cookies

Login Here
 New Subscriptions 
 Buddies Online