RunRyder RC
WATCH
 1 page 2109 views POST REPLY
03-08-2012 05:47 AM  6 years agoPost 1
Dr.Ben

rrMaster

Richmond, VA, USA

My Posts: All  Forum  Topic

For those of you planning on doing a 6S Embla or who may be wondering about other pack choices, Voltz 6S 1300's fit easily under the canopy.

Ben Minor

Peak Aircraft/Team Minicopter Team Futaba Team Kontronik USA

PM  EMAIL  GALLERY  Attn:RR  Quote
03-08-2012 05:55 AM  6 years agoPost 2
T-rexn8

rrKey Veteran

CoLoRaDo

My Posts: All  Forum  Topic

Cool. What motor you end up with?

Xxtreme 800, TDR, 700E DFC, Mini Protos, T-450 DFC, Blade 130x, mcpx, nano

PM  EMAIL  GALLERY  Attn:RR  Quote
03-09-2012 04:28 AM  6 years agoPost 3
Dr.Ben

rrMaster

Richmond, VA, USA

My Posts: All  Forum  Topic

Scorpion 2010 V2 on an ICE50 Lite. It all bolts up nicely with no mods needed. I'll likely use a 12T pinion for now with a little less headspeed because I have some high(er) risk orientation practice for which I plan to use this model, and I want to maximize flight time while still keeping the aeros intact. FBL is a good thing.....

BTW, if any of you get the idea of trying an Align motor, forget it unless you feeling like cutting and/or grinding. The Align bolt pattern is nonstandard as compared to the OEM motor and a Scorpion.

Ben Minor

Peak Aircraft/Team Minicopter Team Futaba Team Kontronik USA

PM  EMAIL  GALLERY  Attn:RR  Quote
06-15-2012 12:16 PM  6 years agoPost 4
gouki

rrVeteran

philippines

My Posts: All  Forum  Topic

good thing i came across this! i was about to get an align motor will a ( i presume ) v1 2010kv scorpion motor mount fine on the embla? the only 2010kv motor available where i will be getting one isn't a v2. thanks

PM  EMAIL  GALLERY  Attn:RR  Quote
06-15-2012 01:56 PM  6 years agoPost 5
KevinB

rrKey Veteran

Saskatoon, Saskatchewan, Canada

My Posts: All  Forum  Topic

Outrage 6s 1300 packs also fit with no mods. And they are rated for 5c charging. I've been balance charging at just over 4c and that gives a 15-20 minutes charge time.

Ben, I have my Emblas set up for a 3200 idle2 and 3000 idle1. At 3200 I get 4:30-4:45 depending on how hard I'm flying. At 3000, it still flys great, just not quite the same collective punch, and I can get 5:00+ ( I leave the timer at 5 but it takes less than 80% out of the pack )
For these headspeeds and governered, I would highly recommend a 13T. 12T doesn't give the gov anything to work with. fyi I'm running a YGE 60a esc.
If you are going even lower, then a 12T may work.

KevinB

PM  EMAIL  GALLERY  Attn:RR  Quote
06-16-2012 02:24 AM  6 years agoPost 6
TMoore

rrMaster

Cookeville, TN

My Posts: All  Forum  Topic

Even on 3s the the 13T is better than the 12T.

Delayed Response Operator Not Engaged
AMA SECTION 336 = Good
Drones = EVIL

PM  EMAIL  HOMEPAGE  GALLERY  Attn:RR  Quote
06-16-2012 02:58 AM  6 years agoPost 7
gouki

rrVeteran

philippines

My Posts: All  Forum  Topic

what pinion gears are you guys using? will the align be okay? i would like to try the 13t pinion also

PM  EMAIL  GALLERY  Attn:RR  Quote
06-16-2012 03:45 AM  6 years agoPost 8
KevinB

rrKey Veteran

Saskatoon, Saskatchewan, Canada

My Posts: All  Forum  Topic

I am using Revco pinions.

KevinB

PM  EMAIL  GALLERY  Attn:RR  Quote
06-16-2012 03:53 AM  6 years agoPost 9
gouki

rrVeteran

philippines

My Posts: All  Forum  Topic

thanks! i just checked out readyhelis and there are so many revco pinions to choose from! what should i pick from those? sorry about these questions, i'm a total noob

PM  EMAIL  GALLERY  Attn:RR  Quote
06-16-2012 05:03 AM  6 years agoPost 10
TMoore

rrMaster

Cookeville, TN

My Posts: All  Forum  Topic

Whatever pinion you get make sure it matches the motor shaft OD.

Delayed Response Operator Not Engaged
AMA SECTION 336 = Good
Drones = EVIL

PM  EMAIL  HOMEPAGE  GALLERY  Attn:RR  Quote
06-16-2012 09:51 AM  6 years agoPost 11
gouki

rrVeteran

philippines

My Posts: All  Forum  Topic

i got the shaft diameter. it's the 0.5m-1.0m i have no clue what to pick

PM  EMAIL  GALLERY  Attn:RR  Quote
06-16-2012 12:32 PM  6 years agoPost 12
KevinB

rrKey Veteran

Saskatoon, Saskatchewan, Canada

My Posts: All  Forum  Topic

If you are using a Scorpion 2010kv motor, get this one:

HO-0500H-13T RevCo "Hard One" 0.5M, Hardened Pinion Gear, 3.17mm Shaft Diameter 13T

KevinB

PM  EMAIL  GALLERY  Attn:RR  Quote
06-16-2012 12:36 PM  6 years agoPost 13
gouki

rrVeteran

philippines

My Posts: All  Forum  Topic

thanks!

PM  EMAIL  GALLERY  Attn:RR  Quote
WATCH
 1 page 2109 views POST REPLY
 Print TOPIC  Make Suggestion 

 5  Topic Subscribe

Sunday, September 23 - 3:37 am - Copyright © 2000-2018 RunRyder   EMAILEnable Cookies

The RC discussion world needs to consolidate. RR is now one choice for that. Its software is cutting edge. It hosts on-topic advertising. Help RR increase traffic buy making suggestions, posting in RR's new areas (sites) and by spreading the word.

The RunRyder Difference

• Category system to allow Rep/Vendor postings.
• Classifieds with sold (hidden) category.
• Classifieds with separate view new.
• Answer PMs offsite via email reply.
• Member gallery photos with advanced scripting.
• Gallery photo viewer integrated into postings.
• Highly refined search with advanced back end.
• Hosts its own high end fast response servers.
• Hosts thousands of HD event coverage videos.
• Rewrote entire code base with latest technology.
• No off-topic (annoying) click bait advertising.
Login Here
 New Subscriptions 
 Buddies Online