RunRyder RC
 1  Topic Subscribe
WATCH
 1 page 2605 views POST REPLY
HomeAircraftHelicopter
e-
Mikado
Logo 400 › My new logo 400 se
11-19-2011 07:08 PM  6 years agoPost 1
piranhafreak

rrVeteran

Manahawkin NJ

My Posts: All  Forum  Topic

Hey all just built my 1st logo. Figured i would go with the 400se as i am on a budget and with that in mind anyone have any recommendations as far as electronics setup? Any help would be great!



Mabey one day i will actually land one of these things !!

PM  EMAIL  GALLERY  Attn:RR  Quote
11-20-2011 09:33 AM  6 years agoPost 2
Paul Gleeson

rrApprentice

Bonn, Germany

My Posts: All  Forum  Topic

Welcome to the logo club!

my spec is

Futaba 9650 servos for cyclic
Futaba BLS251 servo for tail

Mini V-Bar

Hacker X70 SB Pro esc
Hacker A40-10L motor

Voltz 3300mah 35c 6S

Edge 473 mains and Edge 86 tails. The 72 tails are a bit small

18T mod 0.5 pinion running 1900 rpm for smooth sport flying for 9mins

The servos are top-end but you will notice the difference.
I did have Savox 1350s on the cyclic before and these did not center so well.
Also has a midi servo on the tail, and a full size servo made a difference as well.

PM  EMAIL  Attn:RR  Quote
12-10-2011 11:03 PM  6 years agoPost 3
bigben1165

rrKey Veteran

grand rapids, michigan

My Posts: All  Forum  Topic

I am getting the same logo 400se on monday! what electronics did you go with?

big ben - e550 fbl - DX6

PM  EMAIL  GALLERY  Attn:RR  Quote
12-25-2011 04:52 PM  6 years agoPost 4
bigben1165

rrKey Veteran

grand rapids, michigan

My Posts: All  Forum  Topic

hey, just finished my logo 400se:
hyperion 3026-1400
flightpower esc 80 amp.
futaba 9650x3
futaba 9257 tail
edge 475mm
edge tails
full size vbar
various pinions .5
voltz 6s 2600mah
spektrum 6115e receiver
spektrum DX6i

love it!

big ben - e550 fbl - DX6

PM  EMAIL  GALLERY  Attn:RR  Quote
12-25-2011 10:50 PM  6 years agoPost 5
Jays200

rrNovice

Perth, Western Australia

My Posts: All  Forum  Topic

Stretched my 400 to 400SE

Mini Pyro 20-08 1400kV with 17T pinion
Jive 80+HV
MKS 9660A+ cyclics
JR 8900 tail
86mm Edge tails with Logo 500 vertical fin
mini vbar 5.2 with two sats
DX8 with telemetry
Hyperion EX 45C 3300's
0.5 Mod
HS 2200 for about 4:30-5:00 or 2400 for about 30 secs less

Well worth the stretch and gained about 30 secs extra flight time.

Cheers,

Jays

Logo 800 Xx, Logo 600SX, Logo 400SE
Kontronik ESC and Pyro, Vbar

PM  EMAIL  Attn:RR  Quote
12-26-2011 03:06 AM  6 years agoPost 6
bigben1165

rrKey Veteran

grand rapids, michigan

My Posts: All  Forum  Topic

how would about 2000 on the head be?

big ben - e550 fbl - DX6

PM  EMAIL  GALLERY  Attn:RR  Quote
12-26-2011 09:14 AM  6 years agoPost 7
Paul Gleeson

rrApprentice

Bonn, Germany

My Posts: All  Forum  Topic

I fly with 1900 and it's great for sports flying and slow 3d.
With 3300 6s I get 9 mins per pack.

PM  EMAIL  Attn:RR  Quote
12-26-2011 09:53 AM  6 years agoPost 8
arhennie

rrApprentice

Norway

My Posts: All  Forum  Topic

Mine is shaking badly on 1800, a little better but still bad on 2200, and ok on 2350. I only had two flights so far, and on the end of the last flight the aileron started drifting. Probably due to vibrations.

I have a mini v-bar behind the mast, mounted to a plexiglass plate glued to the shelf back there. I have tried my best to get the main gear and tail gear to align properly, as well as mesh should be ok.

But how important is belt tension on this thing? I was flying in cold weather, and the boom have probaly shrinked a little during the time. It did not seem too loose, but need it to be very tight?

arhennie

PM  EMAIL  HOMEPAGE  GALLERY  Attn:RR  Quote
12-26-2011 09:57 AM  6 years agoPost 9
Jays200

rrNovice

Perth, Western Australia

My Posts: All  Forum  Topic

I prefer to run my belt on the looser side.

If you hold the main gear and then try and turn the tail around by hand, if the belt doesn't jump then it's tight enough. More problems from too tight than not tight enough.

Cheers,

Jayson

Logo 800 Xx, Logo 600SX, Logo 400SE
Kontronik ESC and Pyro, Vbar

PM  EMAIL  Attn:RR  Quote
12-27-2011 12:13 AM  6 years agoPost 10
bigben1165

rrKey Veteran

grand rapids, michigan

My Posts: All  Forum  Topic

im setting mine up to run about 2200 rpm.

big ben - e550 fbl - DX6

PM  EMAIL  GALLERY  Attn:RR  Quote
WATCH
 1 page 2605 views POST REPLY
HomeAircraftHelicopter
e-
Mikado
Logo 400 › My new logo 400 se
 Print TOPIC  Make Suggestion 

 1  Topic Subscribe

Thursday, June 21 - 7:23 pm - Copyright © 2000-2018 RunRyder   EMAILEnable Cookies

Login Here
 New Subscriptions 
 Buddies Online