RunRyder RC
WATCH
 1 page 926 views POST REPLY
Home✈️Aircraft🚁Helicoptere-AlignT-REX 700 › 700E main gear strip
06-05-2011 05:20 AM  8 years ago
Topic Vote0Post 1
Tommy8275

rrVeteran

Mount Juliet, TN

MyPosts All Forum Topic
700E main gear strip
Have anyone had a amin gear strip on the 700E? I had mine striped today after switch to ST1 I have a slant gear with 12T pion and KDE motor mount my setup is ESC 120HV kontronic Scorpion 4035-530 HS 2105 Jive gov ST1 ST2 65% flat throttle 12S 5000Mah 13- 13+ degree pitch FBL Vbar. After I striped I did replace the straight main and pion tooth and it strip again, I also had a friend whos help me to adjuast the gear mess to make sure it proper set. Any idea what cause it? I will try again tomorrow with KDE main 115T (straight) see if it still do the same thing
Tommy K
SHARE  PM  EMAIL  GALLERY  Attn:RR  Quote
06-05-2011 06:25 AM  8 years ago
TrevJonez

rrKey Veteran

St.George, Utah - USA

MyPosts All Forum Topic
the thing that makes em strip on my heli is when i have the gov gain turned up too high.

also you can think about adding the 3rd bearing block from KDE a very nice addition to the heli.
Who cares... its just money...
SHARE  PM  EMAIL  GALLERY  Attn:RR  Quote
06-05-2011 12:15 PM  8 years ago
jsenicka

rrProfessor

Eagle River, WI

MyPosts All Forum Topic
http://www.kdedirect.com/TREX700TBB.html
I also had a friend whos help me to adjuast the gear mess to make sure it proper set. Any idea what cause it?
You also want to get gears set to proper mesh or your will have a mess
Jim Senicka
Team Manager, GrandRC Flight Team
SHARE  PM  EMAIL  GALLERY  Attn:RR  Quote
06-05-2011 02:33 PM  8 years ago
dizzymarkus

rrVeteran

Oswego, NY

MyPosts All Forum Topic
I just went through this on maiden flight -- I have the following:
Scorpion 4035-560
11t
Straight KDE NON- HD 115 gear
Scorpion mod1 pinion
Throttle endpoints no gov

Melted the main gear so much when I landed and it cooled I could not move the motor or the gear. Actually melted bits into the pinion and I had to clean that out before reusing. I did some researching and found I had the mesh to tight as the KDE gear swells a touch under heat. New HD gear and much looser mesh -- second flight all is well -- Im still smiling lol

Markus
I reject your reality and substitute my own :0)
SHARE  PM  EMAIL  HOMEPAGE  GALLERY  Attn:RR  Quote
06-06-2011 01:48 PM  8 years ago
Richardmid1

rrProfessor

Leeds, England

MyPosts All Forum Topic
I even stripped 2 of Aligns slanted pinions in mine! They should make steel ones.60% of the time, it works every time!
SHARE  PM  EMAIL  HOMEPAGE  GALLERY  Attn:RR  Quote
06-06-2011 03:02 PM  8 years ago
Tommy8275

rrVeteran

Mount Juliet, TN

MyPosts All Forum Topic
Finally I replaced my KDE main gear eveything was fineTommy K
SHARE  PM  EMAIL  GALLERY  Attn:RR  Quote
06-07-2011 12:42 AM  8 years ago
dizzymarkus

rrVeteran

Oswego, NY

MyPosts All Forum Topic
Tommy if your stripping gears its too loose -- if your melting them its too tight -- ask me how I know hehehe -- theres a fineline I noticed to getting it exactly right -- 5 flights on mine and not babying it at all no problems :0)

Markus
I reject your reality and substitute my own :0)
SHARE  PM  EMAIL  HOMEPAGE  GALLERY  Attn:RR  Quote
06-07-2011 10:04 AM  8 years ago
Richardmid1

rrProfessor

Leeds, England

MyPosts All Forum Topic
Is the KDE main gear any quieter than the standard Align straight cut gear?60% of the time, it works every time!
SHARE  PM  EMAIL  HOMEPAGE  GALLERY  Attn:RR  Quote
06-07-2011 10:57 AM  8 years ago
dizzymarkus

rrVeteran

Oswego, NY

MyPosts All Forum Topic
never used the stock gear sorry I cant answer there

Markus
I reject your reality and substitute my own :0)
SHARE  PM  EMAIL  HOMEPAGE  GALLERY  Attn:RR  Quote
06-07-2011 01:52 PM  8 years ago
Richardmid1

rrProfessor

Leeds, England

MyPosts All Forum Topic
http://www.fast-lad.co.uk/store/bev...41-p-14812.html

Expensive but at least it will survive a crash!
60% of the time, it works every time!
SHARE  PM  EMAIL  HOMEPAGE  GALLERY  Attn:RR  Quote
06-07-2011 04:24 PM  8 years ago
HarveyR

rrVeteran

France - North

MyPosts All Forum Topic
Got over 100 flights now with the stock Align pinion and gear (in fact the full stock 700E Super Combo, 700MX/CC120HV) and no problem so far. In my experience it's a perfect machine/combo as it comes (sorry for those with all the problems...).

Running 1900 RPM CC SetRPM mode (8% gain) with full 12° pitch manoeuvers (tic tocs for example), but I do tend to fly mostly "soft 3D".

What HS are you running?
SHARE  PM  EMAIL  GALLERY  Attn:RR  Quote
06-07-2011 04:26 PM  8 years ago
The Old Guy

rrVeteran

UK Surrey

MyPosts All Forum Topic
http://www.fast-lad.co.uk/store/bev...60-p-14808.html

Maybe this would help solve the problem?
SHARE  PM  EMAIL  HOMEPAGE  GALLERY  Attn:RR  Quote
WATCH
 1 page 926 views POST REPLY
Home✈️Aircraft🚁Helicoptere-AlignT-REX 700 › 700E main gear strip
 Print TOPIC  Make Suggestion 

 6  Topic Subscribe

Monday, June 1 - 9:15 am - Copyright © 2000-2020 RunRyder   EMAILEnable Cookies

Login Here
 New Subscriptions 
 Buddies Online