RunRyder RC
WATCH
 1 page 591 views POST REPLY
06-01-2011 05:14 AM  8 years ago
Topic Vote0Post 1
bstafford

rrNovice

Mansfield, United Kingdom

MyPosts All Forum Topic
Gyro & Rotor Issue
Hello Group,
Have an issue need help with.

Looking for advice on how to fix my Gyro / Rudder on my Shuttle Z+.

Currently using the following components:
1. Sanwa RD6000 Sport TX
2. Sanwa RX-611 Receiver
3. ICG-401 Gyro
4. Futaba S3003 Servo

Main problem on this is the Rudder is stable until I get to about half throttle on the radio and then it starts spinning.

Have now gone thru the alignment setup of the Sanwa RD-6000 and using Normal Mode for Heli and Ch 2, I have 1st set the "G" then "REV" and set to "NOR", which I believe is Head Hold condition, is this correct? Also on "RU" the "REV" and set to "NOR". I have set everything else to default for setting this radio up according to procedure and the Radio is functioning properly as far as ability to get all settings to the manual.

My radio of course has 4 channels and they have all been set for Heli as I have no aircraft as I am only a Heli man. Anyway have tried all 4 channels to make sure there was no issue with an individual channel and they all check out the same.

Have completed the Gyro adjustment on the Radio and have the setup for Normal Mode and Mode 1.

Anyone have an ideas or suggestions please, also to tell you I am a beginner on Heli's, but have done my reading of the Shuttle manual and Sanwa TX manual and do understand and have the knowledge I feel.

However, that said, this is my 1st one I am trying out.

Thanks in advance for any help.

Regards

Bill
SHARE  PM  EMAIL  HOMEPAGE  Attn:RR  Quote
06-01-2011 05:18 AM  8 years ago
TMoore

rrMaster

Cookeville, TN

MyPosts All Forum Topic
The REVO mix is still on. Turn it off.
TM
Part 107.
The only ZERO flight hour certificate in the world.
It's like getting a driver's license without the driver's test.
SHARE  PM  EMAIL  HOMEPAGE  GALLERY  Attn:RR  Quote
06-01-2011 06:05 AM  8 years ago
bstafford

rrNovice

Mansfield, United Kingdom

MyPosts All Forum Topic
Hi TM,

Thanks for reply on this, so just to confirm I have the settings for Revolution Mixing for RV-L - RV-M - RV-H are all at 0%, in defaul Mode-N the settings are RV-L = 20% - RV-M = 0% - RV-H = -20%, all other Modes are at 0%, but decided to set all of them to 0%.

By doing this, this turns off the REVO MIX? I see nothing else in the Radio settings to switch off, just to turn down the %.

Have I missed something here or miss-understand?

Thanks for the help, really appreciate this.

Regards

Bill
SHARE  PM  EMAIL  HOMEPAGE  Attn:RR  Quote
06-01-2011 06:16 AM  8 years ago
bstafford

rrNovice

Mansfield, United Kingdom

MyPosts All Forum Topic
Gyro & Rotor Issue
Hi,

I do have another question to understand better for this "RU" & "G" settings in the "REV" radio setting.

If I am standing in from of the Heli, the Head facing me, tail away, which direction using the radio stick should the rotor move? Is the correct setting for the stick and rotor movement to be the same direction for proper Heli flying direction?

Sorry if this seems a stupid question, but as a newbie, not seen yet in my documents or online in forums this answer or explanation, forgive me.

Regards

Bill
SHARE  PM  EMAIL  HOMEPAGE  Attn:RR  Quote
WATCH
 1 page 591 views POST REPLY
 Print TOPIC  Make Suggestion 

 2  Topic Subscribe

Wednesday, May 27 - 9:45 am - Copyright © 2000-2020 RunRyder   EMAILEnable Cookies

Login Here
 New Subscriptions 
 Buddies Online