RunRyder RC
WATCH
 1 page 1065 views POST REPLY
05-09-2011 10:00 PM  7 years agoPost 1
The3dcrasher

rrNovice

Peabody MA USA

My Posts: All  Forum  Topic

Hey guys. I need setup advice on BEASTX and VELOCITY 90. I have been trying to set up beast on flybarless velocity 90. set up point I cyclic geometry has me stumped. I cant get a blue light until 7.5 degrees. I started with balls 30mm apart from each other on servo horn and now down to 15mm. I literally have spent 4 days trying to get this right. There has to be someone with a beast in a Velocity 90 that can give me some pointers.

PM  EMAIL  GALLERY  Attn:RR  Quote
06-05-2011 12:59 AM  7 years agoPost 2
LongVu78

rrApprentice

MASS

My Posts: All  Forum  Topic

It's me Long.
Can you get a blue light at 6 degrees yet?

Thanks Long

PM  EMAIL  HOMEPAGE  GALLERY  Attn:RR  Quote
06-06-2011 12:54 AM  7 years agoPost 3
The3dcrasher

rrNovice

Peabody MA USA

My Posts: All  Forum  Topic

Hey Long! Got the blue light thanks to your help at the field. So now I have another problem. The Heli after doing tic tocs, piros I then hover and the heli knife edges to the right. It feels like tons of expo on stick. My thought was maybe to move Beast off front side of Heli and to put Beast up on top of frame closer to main shaft. Also 3m tape instead of stock tape. Your thoughts? Vibration?

PM  EMAIL  GALLERY  Attn:RR  Quote
06-06-2011 01:15 AM  7 years agoPost 4
LongVu78

rrApprentice

MASS

My Posts: All  Forum  Topic

You should def try that, like you said move the BeastX on top front and use the 3m tape then it should be perfect. Let me know how it goes.

Thanks Long

PM  EMAIL  HOMEPAGE  GALLERY  Attn:RR  Quote
06-10-2011 06:58 AM  7 years agoPost 5
crashagain

rrApprentice

Redding

My Posts: All  Forum  Topic

The sharp roll to the right or left is vibrations. These things are super sensitive. Use the 3mm tape or strap it down super tight and it should take care of your problem. If not then you have a bearing setting it off.

Velocity 50 FBL, Trex 600 FBL, Frenzy V2 FBL

PM  EMAIL  GALLERY  Attn:RR  Quote
06-13-2011 03:46 AM  7 years agoPost 6
The3dcrasher

rrNovice

Peabody MA USA

My Posts: All  Forum  Topic

Hey guys I just switched the position of beast, I used 3m tape and strapped it on top of heli near main shaft. I hope to fly if not raining tomorrow. Ill let you know how It flys. Thanks.

PM  EMAIL  GALLERY  Attn:RR  Quote
06-14-2011 12:50 AM  7 years agoPost 7
The3dcrasher

rrNovice

Peabody MA USA

My Posts: All  Forum  Topic

I flew Velocity 90 today. The Beast felt better. I was only able to fly once because I autoed the heli and came in fast and stubbed the tail blade into the ground. I ruined the tail blade. The gears seem fine, I thought looking at the blade that the stock blade was realy thin. I hit the ground just barely and one blade folded in half. I had bought new ones (SAB's) but didn't bring them.
Question Do you guys use the LYNX MOAS fuel clunk? Does it need to be weighted? Tips and tricks? Thanks

PM  EMAIL  GALLERY  Attn:RR  Quote
WATCH
 1 page 1065 views POST REPLY
 Print TOPIC  Make Suggestion 

 2  Topic Subscribe

Thursday, September 20 - 4:15 pm - Copyright © 2000-2018 RunRyder   EMAILEnable Cookies

The RC discussion world needs to consolidate. RR is now one choice for that. Its software is cutting edge. It hosts on-topic advertising. Help RR increase traffic buy making suggestions, posting in RR's new areas (sites) and by spreading the word.

The RunRyder Difference

• Category system to allow Rep/Vendor postings.
• Classifieds with sold (hidden) category.
• Classifieds with separate view new.
• Answer PMs offsite via email reply.
• Member gallery photos with advanced scripting.
• Gallery photo viewer integrated into postings.
• Highly refined search with advanced back end.
• Hosts its own high end fast response servers.
• Hosts thousands of HD event coverage videos.
• Rewrote entire code base with latest technology.
• No off-topic (annoying) click bait advertising.
Login Here
 New Subscriptions 
 Buddies Online