RunRyder RC
 1  Topic Subscribe
WATCH
 1 page 384 views TOPIC CLOSED
HomeAircraftHelicopterMain Discussion › modelavionics throttle jockey
01-02-2011 02:33 AM  7 years agoPost 1
Mykey heli

rrNovice

QUARTZ HILL, CA.

My Posts: All  Forum  Topic

i am trying to calibrate my gov. and after turning it on your to flip the gear switch and get a green blinking light, my light stays steady. i have installed seven of these gov's with no problem. checked everything twice ok... can someone please assist me...........thank you buy the way i am using a 9503 jr tx.

YESTERDAY IS GONE AND TOMORROW HAS NOT YET ARRIVED..NOW IS ALL THERE IS...GO FLY...

PM  EMAIL  HOMEPAGE  GALLERY  Attn:RR
01-02-2011 02:43 AM  7 years agoPost 2
steve 01

rrProfessor

Grand Rapids MI

My Posts: All  Forum  Topic

Try lowering the throttle ATV to 90 and try again

PM  EMAIL  GALLERY  Attn:RR
01-02-2011 02:57 AM  7 years agoPost 3
Mykey heli

rrNovice

QUARTZ HILL, CA.

My Posts: All  Forum  Topic

tryed lowering atv but no response...thanks

YESTERDAY IS GONE AND TOMORROW HAS NOT YET ARRIVED..NOW IS ALL THERE IS...GO FLY...

PM  EMAIL  HOMEPAGE  GALLERY  Attn:RR
01-02-2011 02:59 AM  7 years agoPost 4
steve 01

rrProfessor

Grand Rapids MI

My Posts: All  Forum  Topic

It cannot be reaching the endpoints, Do you have one atv at 0 and the other at 100 ?

PM  EMAIL  GALLERY  Attn:RR
01-02-2011 03:05 AM  7 years agoPost 5
Mykey heli

rrNovice

QUARTZ HILL, CA.

My Posts: All  Forum  Topic

both end points at 100%

YESTERDAY IS GONE AND TOMORROW HAS NOT YET ARRIVED..NOW IS ALL THERE IS...GO FLY...

PM  EMAIL  HOMEPAGE  GALLERY  Attn:RR
01-02-2011 03:06 AM  7 years agoPost 6
altima1779

rrKey Veteran

Toledo, oh u.s

My Posts: All  Forum  Topic

Make sure that in your set up screen you have gov mode off and channel set to active. After calibration you can switch channel back to gov. Mode.

PM  EMAIL  HOMEPAGE  GALLERY  Attn:RR
01-02-2011 03:07 AM  7 years agoPost 7
Mykey heli

rrNovice

QUARTZ HILL, CA.

My Posts: All  Forum  Topic

i have gear active....

YESTERDAY IS GONE AND TOMORROW HAS NOT YET ARRIVED..NOW IS ALL THERE IS...GO FLY...

PM  EMAIL  HOMEPAGE  GALLERY  Attn:RR
01-02-2011 03:08 AM  7 years agoPost 8
steve 01

rrProfessor

Grand Rapids MI

My Posts: All  Forum  Topic

If you are setting up on the gear channel one has to be at 0 and the other at 100 then you flip the switch 2 times while booting up

PM  EMAIL  GALLERY  Attn:RR
01-02-2011 03:11 AM  7 years agoPost 9
Mykey heli

rrNovice

QUARTZ HILL, CA.

My Posts: All  Forum  Topic

what do you mean one at 0 and the other at 100?

YESTERDAY IS GONE AND TOMORROW HAS NOT YET ARRIVED..NOW IS ALL THERE IS...GO FLY...

PM  EMAIL  HOMEPAGE  GALLERY  Attn:RR
01-02-2011 03:14 AM  7 years agoPost 10
steve 01

rrProfessor

Grand Rapids MI

My Posts: All  Forum  Topic

When you flip the switch one needs to be set at 0 and flip the switch to the other mode and it needs to be at 100 this will allow you to enter to calibrate the throttle, then you need to change the numbers to set the headspeed

PM  EMAIL  GALLERY  Attn:RR
01-02-2011 03:28 AM  7 years agoPost 11
Mykey heli

rrNovice

QUARTZ HILL, CA.

My Posts: All  Forum  Topic

thanks for all your help i figured it out, i just finished my raptor x50 and had the throttle sw. reversed...not good

YESTERDAY IS GONE AND TOMORROW HAS NOT YET ARRIVED..NOW IS ALL THERE IS...GO FLY...

PM  EMAIL  HOMEPAGE  GALLERY  Attn:RR
WATCH
 1 page 384 views TOPIC CLOSED
HomeAircraftHelicopterMain Discussion › modelavionics throttle jockey
 Print TOPIC  Make Suggestion 

 1  Topic Subscribe

Thursday, June 21 - 11:04 pm - Copyright © 2000-2018 RunRyder   EMAILEnable Cookies

Login Here
 New Subscriptions 
 Buddies Online