RunRyder RC
WATCH
 1 page 2377 views POST REPLY
HomeRC & Power✈️Aircraft🚁Helicoptere-Electric Motors-Controllers-ESCOther › CC BEC Pro how to tell if V1 or V2?
10-15-2010 06:00 PM  8 years ago
Topic Vote0Post 1
flyride

rrKey Veteran

Salt Lake City UT

MyPosts All Forum Topic
CC BEC Pro how to tell if V1 or V2?
My lhs has them but they dont know if v1 or v2 so how can I tell the difference? They said it doesnt say anywhere on the package or bec itself.
and the blonde said "RECTUM, Hell damn near killed em!!"
SHARE  PM  EMAIL  GALLERY  Attn:RR  Quote
10-16-2010 02:10 AM  8 years ago
WATCH-THIS!

rrVeteran

NW Michigan. Rotor Rebels

MyPosts All Forum Topic
I believe the v2 is a selectable voltage bec
SHARE  PM  EMAIL  HOMEPAGE  GALLERY  Attn:RR  Quote
10-16-2010 02:33 AM  8 years ago
flyride

rrKey Veteran

Salt Lake City UT

MyPosts All Forum Topic
Selectable by a switch that is on the outside or via castle link? I am looking for something that is easy to spot on the v2 so I know I have the right one.and the blonde said "RECTUM, Hell damn near killed em!!"
SHARE  PM  EMAIL  GALLERY  Attn:RR  Quote
10-16-2010 04:30 AM  8 years ago
rapidity

rrVeteran

ohio

MyPosts All Forum Topic
Ver 2 should have a sticker on it saying V2.

Here's a pic I stole from another site showing a v2.

SHARE  PM  EMAIL  GALLERY  Attn:RR  Quote
10-16-2010 03:33 PM  8 years ago
flyride

rrKey Veteran

Salt Lake City UT

MyPosts All Forum Topic
Ya I have seen that pic but I dont know if my lhs would like me cracking all of them open in the store to find out. they said over the phone that there wasnt a sticker or anything that said v2 or anything so I will assume it is the v1 as the sticker seems to be the only way to tell from the outside.and the blonde said "RECTUM, Hell damn near killed em!!"
SHARE  PM  EMAIL  GALLERY  Attn:RR  Quote
10-16-2010 11:08 PM  8 years ago
mlucia

rrKey Veteran

Essex Jct., Vermont

MyPosts All Forum Topic
Mine had a V2 sticker right on the side of the case.
SHARE  PM  EMAIL  GALLERY  Attn:RR  Quote
10-17-2010 01:54 AM  8 years ago
Nasscar][

rrVeteran

Delaware

MyPosts All Forum Topic
No sticker, then it's safe to say that you have a V1.

SEND IT BACK TO CC for a replacement.

I almost suffered a total lost but tested and failed at the bench when using 12S.

Nas,
SHARE  PM  EMAIL  HOMEPAGE  GALLERY  Attn:RR  Quote
10-17-2010 02:06 AM  8 years ago
cdrking

rrElite Veteran

Seattle

MyPosts All Forum Topic
The one that is on fire is V1.To hover is divine, the alternative is rather PLANE.
SHARE  PM  EMAIL  GALLERY  Attn:RR  Quote
10-24-2010 09:21 PM  8 years ago
FLYF15

rrNovice

ID

MyPosts All Forum Topic
I took a look at my BEC pro and there were no stickers to indicate if it is a V1 or V2. So I took it apart so I could post a picture. It appears that there is a diode across the outputs. So based on another post, this would lead me to believe this is a V2. Any thoughts? I would like to use this but not until I am sure it is a V2. Thanks.

SHARE  PM  EMAIL  GALLERY  Attn:RR  Quote
10-24-2010 10:27 PM  8 years ago
3Dmuse

rrApprentice

Ontario, Canada

MyPosts All Forum Topic
Mine came with a V2 sticker on the side and looks exactly like yours inside. To be on the safe side though, I would call Castle.
SHARE  PM  EMAIL  Attn:RR  Quote
10-24-2010 10:45 PM  8 years ago
flyride

rrKey Veteran

Salt Lake City UT

MyPosts All Forum Topic
I would say it is a v2 because there is a diode across the output and also a bigger diode that is across the input (blue one). The pics of the v1 only have one diode on the input and it is only connected to the pos. side the v2 has one across the pos and neg. like the one in your pic. Here is a good pic reference a few posts down that was posted by barzaun on another site.
click link here
and the blonde said "RECTUM, Hell damn near killed em!!"
SHARE  PM  EMAIL  GALLERY  Attn:RR  Quote
10-24-2010 10:49 PM  8 years ago
FLYF15

rrNovice

ID

MyPosts All Forum Topic
Thanks guys, I think it is probably safe too but I will be calling castle tomorrow. I will let you know what they say.
SHARE  PM  EMAIL  GALLERY  Attn:RR  Quote
10-25-2010 12:12 AM  8 years ago
3Dmuse

rrApprentice

Ontario, Canada

MyPosts All Forum Topic
I would say it is a v2 because there is a diode across the output and also a bigger diode that is across the input (blue one). The pics of the v1 only have one diode on the input and it is only connected to the pos. side the v2 has one across the pos and neg. like the one in your pic. Here is a good pic reference a few posts down that was posted by barzaun on another site.
click link here
Those are capacitors across the inputs.
SHARE  PM  EMAIL  Attn:RR  Quote
10-25-2010 12:38 AM  8 years ago
flyride

rrKey Veteran

Salt Lake City UT

MyPosts All Forum Topic
Thats what I meant the capacitor diode thingamajig!!!and the blonde said "RECTUM, Hell damn near killed em!!"
SHARE  PM  EMAIL  GALLERY  Attn:RR  Quote
WATCH
 1 page 2377 views POST REPLY
HomeRC & Power✈️Aircraft🚁Helicoptere-Electric Motors-Controllers-ESCOther › CC BEC Pro how to tell if V1 or V2?
 Print TOPIC  Make Suggestion 

 3  Topic Subscribe

Sunday, July 21 - 8:46 am - Copyright © 2000-2019 RunRyder   EMAILEnable Cookies

Login Here
 New Subscriptions 
 Buddies Online