RunRyder RC
WATCH
 1 page 583 views POST REPLY
HomeRC & PowerAircraftHelicopterFlybarless Rotor Head SystemsV-Bar › Servos for Cyclic
04-27-2010 04:38 AM  8 years agoPost 1
TonyC.

rrApprentice

CA

My Posts: All  Forum  Topic

Does FBL require better servo for Cyclic than FB.

Thanks,

PM  EMAIL  Attn:RR  Quote
04-27-2010 04:41 AM  8 years agoPost 2
TrevJonez

rrKey Veteran

St.George, Utah - USA

My Posts: All  Forum  Topic

fbl is more direct to servo so be sure to use plastic servo horns in the event of a crash. also they work load on the servo's is going to be increased but something equivalent to a align 610 or 620 will work fine.

im sure the workload is more becuase my bec was fine on my 600 before i went fbl and after it would brown out under the load.

Who cares... its just money...

PM  EMAIL  GALLERY  Attn:RR  Quote
04-27-2010 08:25 AM  8 years agoPost 3
TonyC.

rrApprentice

CA

My Posts: All  Forum  Topic

Thank you.

PM  EMAIL  Attn:RR  Quote
04-27-2010 09:29 AM  8 years agoPost 4
MrMel

rrProfessor

Gotland

My Posts: All  Forum  Topic

I say it's not a "must" but with better servos comes better performance.
I've seen those that flown with very slow servos, it works, but it dont work as good as faster servos, it all depends on what your expectation is.

But in general, load is higher, so if your FB servos was "just enough", you will benefit more from better servos.

Gone fishing..or hunting..or something
My site: http://heli.dacsa.net - VBar videos and more

PM  EMAIL  GALLERY  Attn:RR  Quote
04-27-2010 02:36 PM  8 years agoPost 5
TonyC.

rrApprentice

CA

My Posts: All  Forum  Topic

Thank you.

PM  EMAIL  Attn:RR  Quote
04-27-2010 08:41 PM  8 years agoPost 6
TonyC.

rrApprentice

CA

My Posts: All  Forum  Topic

I will do JR8917HV for cyclic. Would Fubata9351 be ok with the throttle. Would it make different between 9351 and 8917 for throttle. This is for 90 size heli.

Thanks,

PM  EMAIL  Attn:RR  Quote
04-27-2010 09:06 PM  8 years agoPost 7
Mike545

rrVeteran

gettysburg, pa

My Posts: All  Forum  Topic

you could stick something less expensive on the throttle, 3004

"always feel thankful..... never entitled"

PM  EMAIL  GALLERY  Attn:RR  Quote
04-28-2010 01:10 AM  8 years agoPost 8
TonyC.

rrApprentice

CA

My Posts: All  Forum  Topic

I got used 9351. Just wondering if it ok to use for throttle.

PM  EMAIL  Attn:RR  Quote
04-28-2010 01:13 AM  8 years agoPost 9
TrevJonez

rrKey Veteran

St.George, Utah - USA

My Posts: All  Forum  Topic

in think a 9351 would do great in a throttle position. just set it up and forget about it.

Who cares... its just money...

PM  EMAIL  GALLERY  Attn:RR  Quote
04-28-2010 01:21 AM  8 years agoPost 10
TonyC.

rrApprentice

CA

My Posts: All  Forum  Topic

Thank you very much.

PM  EMAIL  Attn:RR  Quote
WATCH
 1 page 583 views POST REPLY
HomeRC & PowerAircraftHelicopterFlybarless Rotor Head SystemsV-Bar › Servos for Cyclic
 Print TOPIC  Make Suggestion 

 3  Topic Subscribe

Tuesday, October 23 - 4:51 pm - Copyright © 2000-2018 RunRyder   EMAILEnable Cookies

The RC discussion world needs to consolidate. RR is now one choice for that. Its software is cutting edge. It hosts on-topic advertising. Help RR increase traffic buy making suggestions, posting in RR's new areas (sites) and by spreading the word.

The RunRyder Difference

• Category system to allow Rep/Vendor postings.
• Classifieds with sold (hidden) category.
• Classifieds with separate view new.
• Answer PMs offsite via email reply.
• Member gallery photos with advanced scripting.
• Gallery photo viewer integrated into postings.
• Highly refined search with advanced back end.
• Hosts its own high end fast response servers.
• Hosts thousands of HD event coverage videos.
• Rewrote entire code base with latest technology.
• No off-topic (annoying) click bait advertising.
Login Here
 New Subscriptions 
 Buddies Online