RunRyder RC
WATCH
 2 pages [ <<    <    ( 1 )     2     NEXT    >> ] 1167 views POST REPLY
HomeAircraftHelicopterJR Heli Vibe 90/50, Sylphide 90, GSR260 › Vibe 50 with 611......... help
04-06-2010 06:06 PM  8 years agoPost 1
Jacoub

rrKey Veteran

Kuwait

My Posts: All  Forum  Topic

I have 611 with JR9303, Align carbon 95mm tail blades, actually the tail is holding very good but when I do some mid 3d the tail his slightly moving (( until now I didn't switch on thde Governor)).
my radio gain is around 63

I also tried the KBDD 50 size tail blades but they were very bad

Help please, thanks

PM  EMAIL  GALLERY  Attn:RR  Quote
04-06-2010 06:09 PM  8 years agoPost 2
z11355

rrMaster

New England

My Posts: All  Forum  Topic

on the control box for the 611, what is the gain # ?

PM  EMAIL  GALLERY  Attn:RR  Quote
04-06-2010 06:13 PM  8 years agoPost 3
Jacoub

rrKey Veteran

Kuwait

My Posts: All  Forum  Topic

Actual gain in the 611 box is 18

PM  EMAIL  GALLERY  Attn:RR  Quote
04-06-2010 06:16 PM  8 years agoPost 4
BarracudaHockey

rrMaster

Jacksonville FL

My Posts: All  Forum  Topic

Up it to 35 on the gyro amp

Andy
AMA 77227
http://www.jaxrc.com

PM  EMAIL  GALLERY  Attn:RR  Quote
04-06-2010 06:22 PM  8 years agoPost 5
Jacoub

rrKey Veteran

Kuwait

My Posts: All  Forum  Topic

amp ??

PM  EMAIL  GALLERY  Attn:RR  Quote
04-06-2010 06:24 PM  8 years agoPost 6
dasd

rrVeteran

Carol Stream, IL

My Posts: All  Forum  Topic

on the 611 control box (amp) bump it to 35. 18 is too low.

Formerly SunFunFlyer.

PM  EMAIL  GALLERY  Attn:RR  Quote
04-06-2010 06:28 PM  8 years agoPost 7
Jacoub

rrKey Veteran

Kuwait

My Posts: All  Forum  Topic

thanks I will try it tomorrow, but When I did put 75 in the radio it gave me 34, I had I bad tail shacking, I do not think it will work
Also I have changed the mode from std to 3d in 611 box, is that ok

PM  EMAIL  GALLERY  Attn:RR  Quote
04-06-2010 07:05 PM  8 years agoPost 8
dasd

rrVeteran

Carol Stream, IL

My Posts: All  Forum  Topic

Changing the mode to 3d is fine. If you're getting tail hunting at 34, something else is at play with the setup. I'm running 35 on my Vibe and it's rock solid in every maneuver. Make sure the ball on the servo arm is at least 15-16mm out and there is no binding at all.

Formerly SunFunFlyer.

PM  EMAIL  GALLERY  Attn:RR  Quote
04-07-2010 02:15 PM  8 years agoPost 9
BarracudaHockey

rrMaster

Jacksonville FL

My Posts: All  Forum  Topic

What are your LimitA and LimitB set to?

What tail blades are you using?

Andy
AMA 77227
http://www.jaxrc.com

PM  EMAIL  GALLERY  Attn:RR  Quote
04-07-2010 02:32 PM  8 years agoPost 10
darrens

rrKey Veteran

United Kingdom

My Posts: All  Forum  Topic

Could be your tail servo arm is too long, hence you have too much "mechanical" gain. Try moving the ball link inwards and this will allow you to run more "electronic" gain on the gyro.

He who dies with the most toys is the winner!

PM  EMAIL  GALLERY  Attn:RR  Quote
04-08-2010 03:34 AM  8 years agoPost 11
Jacoub

rrKey Veteran

Kuwait

My Posts: All  Forum  Topic

darrens
It is a good point mate, because I was using the JR 770, also I had the same issue, to much gain,

Barracodahoecky, My servo is JR 9800 (mid seginal), Actually I don't know what are they because I didn't change them, I checked them before and they were ok, also on my radio limit I did put 100 for both sides

PM  EMAIL  GALLERY  Attn:RR  Quote
04-08-2010 04:01 AM  8 years agoPost 12
Zaneman007

rrElite Veteran

Texas - USA

My Posts: All  Forum  Topic

I have the 611 in my Vibe, amp gain is mid 20's holds great using the DS1015 servo for the tail. You need to set the limits to max out the travel on the tail servo in both directions. If that is 100 on both sides then your good.

Old Guys Rule!

PM  EMAIL  GALLERY  Attn:RR  Quote
04-08-2010 04:13 AM  8 years agoPost 13
Jacoub

rrKey Veteran

Kuwait

My Posts: All  Forum  Topic

Update, Futaba 611 screen box
LimitB1 is 100
gainn is 34

And, the arm's lenght was 16mm
I have changed it to 15mm
Tail blade was KBDD 50 nielon, and Algin CF 95mm
I tried both, the align blades were much better than other

(( My Radio is JR 9dsx))

PM  EMAIL  GALLERY  Attn:RR  Quote
04-08-2010 10:20 AM  8 years agoPost 14
Saleh

rrVeteran

Kuwait

My Posts: All  Forum  Topic

I have the same setup works fine, my set up is as following
in the trans gyro screen make sure that its set on auto and set the gain in the trans @ 73 and the actual in the amp will be around 35

another thing make sure that the end points in the amp are above 113 in order to get the optimum performance from the gyro

If you aint crashing you aint flyin

PM  EMAIL  HOMEPAGE  GALLERY  Attn:RR  Quote
04-08-2010 11:20 AM  8 years agoPost 15
darrens

rrKey Veteran

United Kingdom

My Posts: All  Forum  Topic

Hi Jacoub,

No problem. Thing to do is make one change at a time. There is lots of good advice here but you really need to do one thing, then test fly to see if there is any improvement.
please update us when you have test flown and resolved the issue.

cheers
Darren

He who dies with the most toys is the winner!

PM  EMAIL  GALLERY  Attn:RR  Quote
04-08-2010 12:55 PM  8 years agoPost 16
Jacoub

rrKey Veteran

Kuwait

My Posts: All  Forum  Topic

Darrens, Salah
Exactly, I did change the lenght of the servo's arm, and it works, this Gyro is an amazing invention

I tested it this day and it was fantastic gyro, but the weather was very bad, it was a bloody hell wind with some light rains, the Vibe is totally deferent with this Gyro,

PM  EMAIL  GALLERY  Attn:RR  Quote
WATCH
 2 pages [ <<    <    ( 1 )     2     NEXT    >> ] 1167 views POST REPLY
HomeAircraftHelicopterJR Heli Vibe 90/50, Sylphide 90, GSR260 › Vibe 50 with 611......... help
04-08-2010 01:48 PM  8 years ago •• Post 17 ••
darrens

rrKey Veteran

United Kingdom

My Posts: All  Forum  Topic

Glad I could help Jacoub, now you can enjoy your Vibe

He who dies with the most toys is the winner!

PM  EMAIL  GALLERY  Attn:RR  Quote
04-08-2010 04:57 PM  8 years agoPost 18
Jacoub

rrKey Veteran

Kuwait

My Posts: All  Forum  Topic

darrens
Cheers mate

PM  EMAIL  GALLERY  Attn:RR  Quote
04-08-2010 06:36 PM  8 years agoPost 19
BarracudaHockey

rrMaster

Jacksonville FL

My Posts: All  Forum  Topic

95mm is pretty big for a vibe, thats got a 90 size tail hub, I run 87 to 92s, that will let your mechanical gain do less and your electronic gain to do a little more.

Andy
AMA 77227
http://www.jaxrc.com

PM  EMAIL  GALLERY  Attn:RR  Quote
04-08-2010 09:00 PM  8 years agoPost 20
Jacoub

rrKey Veteran

Kuwait

My Posts: All  Forum  Topic

BarracudaHockey
Yes, they are, but I tried the KBDD also, it doesn't matter with me, But what do you recommand the best for the Vibe? give me a brand and the size?

PM  EMAIL  GALLERY  Attn:RR  Quote
WATCH
 2 pages [ <<    <    ( 1 )     2     NEXT    >> ] 1167 views POST REPLY
HomeAircraftHelicopterJR Heli Vibe 90/50, Sylphide 90, GSR260 › Vibe 50 with 611......... help
 Print TOPIC  Make Suggestion 

 2  Topic Subscribe

Tuesday, October 23 - 7:00 am - Copyright © 2000-2018 RunRyder   EMAILEnable Cookies

The RC discussion world needs to consolidate. RR is now one choice for that. Its software is cutting edge. It hosts on-topic advertising. Help RR increase traffic buy making suggestions, posting in RR's new areas (sites) and by spreading the word.

The RunRyder Difference

• Category system to allow Rep/Vendor postings.
• Classifieds with sold (hidden) category.
• Classifieds with separate view new.
• Answer PMs offsite via email reply.
• Member gallery photos with advanced scripting.
• Gallery photo viewer integrated into postings.
• Highly refined search with advanced back end.
• Hosts its own high end fast response servers.
• Hosts thousands of HD event coverage videos.
• Rewrote entire code base with latest technology.
• No off-topic (annoying) click bait advertising.
Login Here
 New Subscriptions 
 Buddies Online