RunRyder RC
WATCH
 1 page 830 views POST REPLY
HomeAircraftHelicopterRadio - Futaba FASST › Futaba problems
03-08-2010 06:05 PM  8 years agoPost 1
neverhappy

rrApprentice

Piedmont.Al. USA

My Posts: All  Forum  Topic

Hope this is where I need to post this question.

My futaba CHP is giving me problems everytime I use it all my heli's have a tail wagging problem.

The reason for the problem is the REVO mix is in the on mode without me switching it there. In on and model switching it moves.....

So I'm I going to change it everytime I use it??

jeff

Jeffrey:) (Love and Peace to all)

PM  EMAIL  GALLERY  Attn:RR  Quote
03-08-2010 06:29 PM  8 years agoPost 2
BarracudaHockey

rrMaster

Jacksonville FL

My Posts: All  Forum  Topic

Just turn it off. The 9c (non super) defaults to REVO on (for whatever reason) they fixed it in the Super.

Once you turn it off for each model it should be off for good.

Andy
AMA 77227
http://www.jaxrc.com

PM  EMAIL  GALLERY  Attn:RR  Quote
03-08-2010 06:32 PM  8 years agoPost 3
BeltFedBrowning

rrKey Veteran

Kansas City

My Posts: All  Forum  Topic

I set mine to INH (inhibit) and it stays there on my 9c, my 7c, and my 10c. Have you tried to change it in the advanced menu for all flight modes?

PM  EMAIL  GALLERY  Attn:RR  Quote
03-08-2010 06:52 PM  8 years agoPost 4
neverhappy

rrApprentice

Piedmont.Al. USA

My Posts: All  Forum  Topic

I have did this in the advance mode also. It seems to only do it after the radio sits week to week of flying.

Will flying today and put away after charging and check it again tomorrow.

No off mode in the radio.
Jeff

Jeffrey:) (Love and Peace to all)

PM  EMAIL  GALLERY  Attn:RR  Quote
03-08-2010 07:41 PM  8 years agoPost 5
BarracudaHockey

rrMaster

Jacksonville FL

My Posts: All  Forum  Topic

Off meaning Inhibited

You can also go in and set the rate to all 0's.

If thats changing after your radio sits then I'd get it looked at because if that can change anything (including tail servo direction for example) could change on you.

Andy
AMA 77227
http://www.jaxrc.com

PM  EMAIL  GALLERY  Attn:RR  Quote
03-08-2010 07:51 PM  8 years agoPost 6
chris6414

rrApprentice

Sneads Ferry, NC USA

My Posts: All  Forum  Topic

Advanced menu, Revo, Highlight the "on" roll dial till it says INH. Exit. If you see "ON" it is not inhibited. I just activated mine in my 7CHP. in that menu you also most likely have a switch assigned to that function. Hope this helps.

Century Hawk Sport, OS .32, Futaba 7C, GY-601 9251
Predator Gasser SE G-23, Fut 3010 servos, JR gyro/servo

PM  EMAIL  GALLERY  Attn:RR  Quote
03-09-2010 11:05 PM  8 years agoPost 7
neverhappy

rrApprentice

Piedmont.Al. USA

My Posts: All  Forum  Topic

update
Flew my Predator and 450 today. Radio worked great after I reset all the points to "0" yesterday. It stayed on "INH". So Thank's for all the help. I like the radio since I upgraded it to 2.4.

Jeff

Jeffrey:) (Love and Peace to all)

PM  EMAIL  GALLERY  Attn:RR  Quote
WATCH
 1 page 830 views POST REPLY
HomeAircraftHelicopterRadio - Futaba FASST › Futaba problems
 Print TOPIC  Make Suggestion 

 1  Topic Subscribe

Sunday, August 19 - 8:22 pm - Copyright © 2000-2018 RunRyder   EMAILEnable Cookies

Login Here
 New Subscriptions 
 Buddies Online