RunRyder RC
WATCH
 1 page 1014 views POST REPLY
HomeRC & PowerAircraftHelicopterFlybarless Rotor Head SystemsOther › Mini V Bar with DX7 problem
01-19-2010 10:15 PM  8 years agoPost 1
phil evon

rrApprentice

Central New Jersey

My Posts: All  Forum  Topic

I did the binding process for spektrum with dx7 and all went well. then i started my calibration process. aileron and elevator are fine. when i get to start the collective i notice that when i move the left stick up and down it is moving the rudder bar on the software and when i move the left stick right and left the collective bar moves on the software. i am using 2 satellites. can anyone help on this? thanks

AMA 125840

PM  EMAIL  GALLERY  Attn:RR  Quote
01-19-2010 10:17 PM  8 years agoPost 2
Ronald Thomas

rrMaster

Gainesville, Fl, USA

My Posts: All  Forum  Topic

Do you have the DX-7 selected under the rx expert mode?

Team MikadoUSA 480XXTreme, 550SX, 600SX, 700XXTreme, 800XXTreme!!

PM  EMAIL  GALLERY  Attn:RR  Quote
01-19-2010 10:38 PM  8 years agoPost 3
phil evon

rrApprentice

Central New Jersey

My Posts: All  Forum  Topic

Yes, Dx7 was selected under rx expert mode. I believe it defaulted to dx7 when I chose spektrum but I made sure anyway.

AMA 125840

PM  EMAIL  GALLERY  Attn:RR  Quote
01-19-2010 11:19 PM  8 years agoPost 4
soberflierross

rrApprentice

Cottage Grove, MN USA

My Posts: All  Forum  Topic

had the same problem, watch the 4.0 video on setting up the mini you have the wrong tx selected, you have to rebind

http://www.vstabi.de/V4/index_e.html

PM  EMAIL  GALLERY  Attn:RR  Quote
01-20-2010 04:59 AM  8 years agoPost 5
OICU812

rrMaster

Edson, Alberta, Canada

My Posts: All  Forum  Topic

So what was the deal??

...Once upon a time there were Nitros, flybars and frequency pins...

PM  EMAIL  GALLERY  Attn:RR  Quote
01-20-2010 12:28 PM  8 years agoPost 6
phil evon

rrApprentice

Central New Jersey

My Posts: All  Forum  Topic

Ok, tried it again. Once I select Spektrum I have no other choice than the default DX7. I went through the process again anyway and this time it worked. However, it takes about 3 tries of shutting the power off to the unit to get it to bind. In any case, the channels seemed to be assigned correct now. Thanks for the help.

AMA 125840

PM  EMAIL  GALLERY  Attn:RR  Quote
01-20-2010 07:38 PM  8 years agoPost 7
OICU812

rrMaster

Edson, Alberta, Canada

My Posts: All  Forum  Topic

Once u select did u remove USB cable? If u do it will bind right away.

...Once upon a time there were Nitros, flybars and frequency pins...

PM  EMAIL  GALLERY  Attn:RR  Quote
01-20-2010 09:40 PM  8 years agoPost 8
phil evon

rrApprentice

Central New Jersey

My Posts: All  Forum  Topic

I never did remove the USB cable

AMA 125840

PM  EMAIL  GALLERY  Attn:RR  Quote
01-20-2010 10:32 PM  8 years agoPost 9
OICU812

rrMaster

Edson, Alberta, Canada

My Posts: All  Forum  Topic

Aha, that's why u had bit of issue gettin the bind glad u got it sorted though

...Once upon a time there were Nitros, flybars and frequency pins...

PM  EMAIL  GALLERY  Attn:RR  Quote
01-21-2010 12:35 AM  8 years agoPost 10
phil evon

rrApprentice

Central New Jersey

My Posts: All  Forum  Topic

I was getting very frustrated. Last night I was able to bind, do the centering and end point calibration, installed the servo arms and use the software to get the servo arms at 90 degrees. I just have to do the linkage now to level the swash plate a zero degrees so I'm on my way. After that though, do I set my throws on collective pitch in my pitch curves of the tx or is there somewhere in the software for that? Thanks

AMA 125840

PM  EMAIL  GALLERY  Attn:RR  Quote
01-21-2010 01:06 AM  8 years agoPost 11
Ronald Thomas

rrMaster

Gainesville, Fl, USA

My Posts: All  Forum  Topic

Pitch curves in the tx (0-25-50-75-100). Overall pitch in the VBAR program (slider on the front screen)........Ron

Team MikadoUSA 480XXTreme, 550SX, 600SX, 700XXTreme, 800XXTreme!!

PM  EMAIL  GALLERY  Attn:RR  Quote
WATCH
 1 page 1014 views POST REPLY
HomeRC & PowerAircraftHelicopterFlybarless Rotor Head SystemsOther › Mini V Bar with DX7 problem
 Print TOPIC  Make Suggestion 

 1  Topic Subscribe

Friday, October 19 - 3:42 am - Copyright © 2000-2018 RunRyder   EMAILEnable Cookies

The RC discussion world needs to consolidate. RR is now one choice for that. Its software is cutting edge. It hosts on-topic advertising. Help RR increase traffic buy making suggestions, posting in RR's new areas (sites) and by spreading the word.

The RunRyder Difference

• Category system to allow Rep/Vendor postings.
• Classifieds with sold (hidden) category.
• Classifieds with separate view new.
• Answer PMs offsite via email reply.
• Member gallery photos with advanced scripting.
• Gallery photo viewer integrated into postings.
• Highly refined search with advanced back end.
• Hosts its own high end fast response servers.
• Hosts thousands of HD event coverage videos.
• Rewrote entire code base with latest technology.
• No off-topic (annoying) click bait advertising.
Login Here
 New Subscriptions 
 Buddies Online