RunRyder RC
WATCH |
1 page 395 views | Topic Closed |
| RunRyder | RunRyder |
|
|
0| rcchauffeur
rrApprentice Vancouver BC |
Brand New in box O.S. 18400 .91 SZ-H PH-HYPER W/PUMP OSMG1984 BRAND NEW IN BOX......$300.00 INC SHIPPING TO YOUR DOOR IN USA
PAYPAL ONLY.O.S. 18400 .91 SZ-H PH-HYPER W/PUMP OSMG1984Product DetailsThis is the O.S. Max .91 SZ-H PH Hyper Helicopter Engine with Pump.FEATURES: Redesigned crankcase provides better support for the crankshaft and thrust bearings New 60M 3-needle carburetor with mid-range needle for precise adjustments and push/pull throttle arm for added precision in power control Front and rear ball bearing-supported crankshaft Blue anodized cylinder head with "O.S." and "World Champion's Spec" printed in White at the top of the head Graphite backplate pump mount Two year limited warrantyINCLUDES: O.S. Max .91 SZ-H PH Hyper Helicopter Engine with Pump with #8 glow plug, one .004" (.11mm) head gasket and one .008" (.22mm) head gasket, decals, Woodruff key, needle adjust screw (2.6x5mm) and instruction manualREQUIRES: Fuel: 10%-30% nitromethane with at least 18% lubricant. Lubricants may be either castor or synthetic oil or castor/synthetic blend. Field Equipment: glow starter, fuel bulb, fuel can filter, fuel pump hexagonal starting shaft (depending on brand of helicopter) electric starter, battery and fuel tubing Muffler- This is specific to the heli.SPECS: Displacement: 0.912 cu in (14.95 cc) Bore: 1.02" (25.8mm) Stroke: 0.87" (22mm) Output: 3.3 ps @ 15,000 RPM Practical RPM Range: 2000-16,000 Weight Without Muffler: 22.5oz (640g) Height from crankcase bottom to top of cylinder head: 4.1" (105mm) Height/bottom of mounting tab to top of cylinder head: 3.4" (87.4mm) Distance between mounting holes same side: 0.98" (25mm) Distance between mounting holes opposite side 2.04" (52mm) Distance between muffler screw holes: 1.6" (42mm) Distance/bottom of mounting tab to muffler screw holes: 1.7" (42.8mm) Length from front of case to backplate: 3.3" (84mm) Length from backplate to end of crankshaft: 0.63" (116mm) Width of crankcase below mounting tabs: 1.7" (42.6mm) Width between mounting tabs: 2.4" (61mm)COMMENTS: High speed needle setting - 2-1/2 turns OPEN from fully closed Idle mixture setting - set from the factory Medium speed needle valve - 1-1/2 turn OPEN from fully closed |
| SHARE PM EMAIL Attn:RR | |
| Kobinger
rrApprentice USA |
rcchauffeur aka Randy... Is a good honest guy to deal with.Have had transactions with him in the past, buy with confidence, easy to deal with.Richard |
| SHARE PM EMAIL GALLERY Attn:RR | |
WATCH |
1 page 395 views | Topic Closed |
| RunRyder | RunRyder |
|
|
Classifieds › HELP-FAQ
|
Attention Buyers!
To receive feedback Post Reply in the seller’s topic.
The seller can then click your post's Add Classified Feedback link.
Attention Sellers!
Stating price is not mandatory but recommended. Post Reply commentary that interferes with the selling process
(and not replied to) will be removed upon request. Click Attn:RR on the offending classified post.
Repeated NIB-NIP sales are not allowed. Take it to EBay.
Buyer Beware!
RunRyder cannot vouch for any seller's or buyer's credibility and will not accept responsibility for any transactions resulting from the use of this site.
|
Saturday, January 23 - 10:50 am - Copyright © 2000-2021 RunRyder EMAIL • Enable Cookies
