RunRyder RC
 1 page 311 views Topic Closed
06-15-2009 08:22 AM  11 years ago
Topic Vote0Post 1


Boring Oregon

MyPosts All Forum Topic
Ok, I've got a brand new, never flown Blade 400 PNP. It comes with a brand new sealed Spektrum AR6100E RX, and a Spektrum DX6I Radio. The heli has servos, ESC and gyro installed from the factory. This set also comes with a brand new never flown Airframe front half, with head and tail. The extra heli main frame is new as is the tail unit. See picture. So think of them as replacement parts should anything happen to the new Blade 400 PNP. The head unit has an aftermarket metal swash plate on it. I'm including 2 pictures. One shows the brand new never flown Blade 400 with books and new RX. The other shows the parts included with this sale.
I'm selling all of my Blade 400 stuff except my flying 400 to start saving up for a Trex 450 SE V2

Now, as to the DX6I. This TX had the Recall numbers on it. I sent it in to get the upgrade on it. I flew this TX before sending it in, but while it was in bought a DX7. So I no longer need this TX. It's had the upgrade done at the factory with full factory inspection and testing done, new gimbles installed and new upgraded trim tabs installed. It's ready to go and you don't have to worry about it doing anything freaky on you. I should note that the bottom edge of the battery box door has my name on it. I put it on there as my friend and I both flew DX6I TX's and wanted to ensure we knew them apart.
To fly, you will need a charger and a battery. The new in the box RX needs to be installed in the heli. As I stated, this heli has only been out of the box to view and take picture.

The extra parts included are

2 Eflite main shafts ( also one on the extra frame)
2 used bodies
5 eflite servo rebuild kits
1 new tail belt ( out of package)
1 new pack of fly bar paddles
2 O ring head rebuild kits
1 battery connector kit with 2 female pieces
2 new skid pipes
1 new tail shaft with pully ( included bushings)

As far as the extra air frame goes, it was a new air frame I bought for parts. I used the tail boom on my other blade 400 and the tail belt gear drive. It comes with the tail unit and slider, top mast and new blades. As I recall I took the thrust bearings out of the head though. Either way, the extra air frame is new for parts and included with this set.

I'm looking to get $350 for this complete set up or possible trade for Trex silver 450 SEv2. I don't need a TX as I've got a DX7 and I've got a RX as well. so if you have a V2 and want this setup, let me know.

Contact me via pm or email at
06-15-2009 04:10 PM  11 years ago
Z06 Tony


Rochester NY.

MyPosts All Forum Topic
Great guy to deal with. Very honest man. Did a trade and a few sales with the Cudaman and all his stuff is well taken care of. This is a sweet deal also.
 1 page 311 views Topic Closed

 1  Topic Subscribe

Classifieds › HELP-FAQ
Attention Buyers! To receive feedback Post Reply in the seller’s topic. The seller can then click your post's Add Classified Feedback link.
Attention Sellers! Stating price is not mandatory but recommended. Post Reply commentary that interferes with the selling process (and not replied to) will be removed upon request. Click Attn:RR on the offending classified post. Repeated NIB-NIP sales are not allowed. Take it to EBay.
Buyer Beware! RunRyder cannot vouch for any seller's or buyer's credibility and will not accept responsibility for any transactions resulting from the use of this site.

Tuesday, January 26 - 12:13 am - Copyright © 2000-2021 RunRyder   EMAILEnable Cookies

Login Here
 New Subscriptions 
 Buddies Online