RunRyder RC
WATCH
 1 page 1879 views POST REPLY
HomeAircraftHelicopterFuel-Helicopters New or Limited ActivityOther › Got The MultiGov Pro Working
06-08-2009 01:18 AM  9 years agoPost 1
CEGLOBAL

rrApprentice

Lahaina, Hawaii - United States

My Posts: All  Forum  Topic

Aloha everyone

The MultiGov Pro was connected this past week on my Aeolus 50 3D. I did the setup. Got a half tank in without the MultiGov Pro engaged yesterday. Set the heli down. Cut the OS50. Engaged the MultiGov Pro with programming card and . . . What a difference! I will be definitely using the MultiGov Pro from now on.

Here are the photos of the updated placement of components and cleaner look of the rerouting of the wires

The last photo taken showing the top of the heli. Notice from my other thread, I moved the voltage regulator switch from the top of the electronics pod to the lower part of the right side frame. No more rubbing the canopy causing the rounding of two of the corners of the switch. What that did for me was that it was easier to get to the switch to turn on/off and light the glow plug when the canopy is on the heli at engine startup.

EJB

PM  EMAIL  GALLERY  Attn:RR  Quote
06-08-2009 06:07 AM  9 years agoPost 2
rexxigpilot

rrProfessor

Florida

My Posts: All  Forum  Topic

Interesting looking heli you got there.

You may want to relocate that header tank where it can hang horizontally or secure it well so it doesn't slip out of the bracket from vibration.

You will love the MultiGov.

PM  EMAIL  GALLERY  Attn:RR  Quote
06-08-2009 09:07 AM  9 years agoPost 3
juha76

rrNovice

finland

My Posts: All  Forum  Topic

Hi ceglobal!

You can mount the header tank next to the main tank by using
quicuk header tank mount kit.

PM  EMAIL  HOMEPAGE  GALLERY  Attn:RR  Quote
06-08-2009 10:23 AM  9 years agoPost 4
CEGLOBAL

rrApprentice

Lahaina, Hawaii - United States

My Posts: All  Forum  Topic

Good Point
rexxigpilot

Good point about securing the tank well. Although the tank fits snug in the bracket to a point where I have to use some force, I can see over time the tank wearing and then slipping out. The header tank works a lot better on the right side of the heli as it gives a balance to the muffler on the left side of the heli. So, a couple of options that I could consider to ensure the tank does not slip out is 1) putting a piece of zip tie in between the tank and the bracket or 2) glueing a piece of plastic or zip tie to act as a stopper above the bracket.

What is your opinion?

EJB

PM  EMAIL  GALLERY  Attn:RR  Quote
06-08-2009 10:28 AM  9 years agoPost 5
CEGLOBAL

rrApprentice

Lahaina, Hawaii - United States

My Posts: All  Forum  Topic

juha76

Thanks for the suggestion.

I do have a couple of questions for you.

Have you noticed any vibration from having the header tank out that far from the frame?

Did the header tank come with the bracket from Quik UK and did it come with the red grommet?

EJB

PM  EMAIL  GALLERY  Attn:RR  Quote
06-08-2009 10:32 AM  9 years agoPost 6
CEGLOBAL

rrApprentice

Lahaina, Hawaii - United States

My Posts: All  Forum  Topic

What do you have onboard?
juha76

I would like to know what electronics, engine, and blades you have onboard your Aeolus 50 3D?

Thanks
EJB

PM  EMAIL  GALLERY  Attn:RR  Quote
06-08-2009 11:00 AM  9 years agoPost 7
juha76

rrNovice

finland

My Posts: All  Forum  Topic

Hi

No vibration problems with the header tank. Yes the quickuk header tank comes with the bracket and the red grommet,but the mount kit you have to buy separately.

My Aeolus has futaba s9351 servos for the swash,graupner c577 for throttle,logictech 6100t gyro with 6100g servo,futaba r6014fs receiver,dualsky vr-8l regulator with outrage 2s 2500mah lipo.

Engine is TT redline 53 with hatori 523 pipe,mainblades are
swe 620dc and stock tailblades.

Juha

PM  EMAIL  HOMEPAGE  GALLERY  Attn:RR  Quote
06-08-2009 11:40 AM  9 years agoPost 8
CEGLOBAL

rrApprentice

Lahaina, Hawaii - United States

My Posts: All  Forum  Topic

Thanks
juha

Thanks for the info. I will definitely be looking into the QuikUK products. It wouldn't hurt to bling out the Aeolus 50 3D a little!

EJB

PM  EMAIL  GALLERY  Attn:RR  Quote
WATCH
 1 page 1879 views POST REPLY
HomeAircraftHelicopterFuel-Helicopters New or Limited ActivityOther › Got The MultiGov Pro Working
 Print TOPIC  Make Suggestion 

 1  Topic Subscribe

Wednesday, August 15 - 2:15 am - Copyright © 2000-2018 RunRyder   EMAILEnable Cookies

Login Here
 New Subscriptions 
 Buddies Online