RunRyder RC
WATCH
 18 pages [ <<    <    ( 1 )     2      3     NEXT    >> ] 48637 views POST REPLY
HomeScaleAircraftHelicopterScale Model RC Helicopters Sell  *****SOLD ***** My Hughes MD 500 G Jive
05-05-2009 07:54 AM  9 years agoPost 1
James

rrVeteran

Del Mar California

My Posts: All  Forum  Topic

hi everyone ,
the head is a OF. helitechnik and OF.helitechnik hand made blades very high quality 5 blade rotor head system complete. with these two paired together you will have very smooth steady flight very well balance blades. paid like $100 per blade. tail has futaba 401 gyro and high speed servo , flight servos are futaba, S9551. Complete electronics you only need to provide a spectrum radio like the dx 8 or better SPECTRUM TRAMITTER radio. Has a Ar8000 spectrum 8 channel high speed receiver installed . Mechanics Airstar international A copy of the vario benzene trainer, vario parts will fit mechanics, they built it that way deliberately . I would personally take out the G260 gas engine pull start motor, and buy the vario electric conversion kit which is made for the vario Benzene trainer mechanics, converts perfectly. The scale will fly smoother and sound awesome . Mechanics are new, motor, has never been started. Just pre set up and fly mechanics then install into scale . pull start by opening up back door of scale has complete detail cockpit this scale has over 300 hours put into it lots of detail. I know how to built scale fuselages very well and fly but not good with setting up a 5 head rotor head system have no clue. lost interested in flying because of Airstar international !!!
fuselage was $1200 Paint $300 labor $2500 mechanics$1200 plus $900 for blades and rotor.

been reluctant in selling it make offer

flying is the easy part paying for it whole different story

PM  EMAIL  HOMEPAGE  GALLERY  Attn:RR  Quote
05-05-2009 07:55 AM  9 years agoPost 2
James

rrVeteran

Del Mar California

My Posts: All  Forum  Topic


Mick Pattison, seen standing next to pilot of G Jive. Along with his beautiful scale he built.

This is the scale i will be building.
I will be posting pictures real soon.
Jim

flying is the easy part paying for it whole different story

PM  EMAIL  HOMEPAGE  GALLERY  Attn:RR  Quote
05-05-2009 07:55 AM  9 years agoPost 3
James

rrVeteran

Del Mar California

My Posts: All  Forum  Topic

first day bringing it home

flying is the easy part paying for it whole different story

PM  EMAIL  HOMEPAGE  GALLERY  Attn:RR  Quote
05-05-2009 07:56 AM  9 years agoPost 4
James

rrVeteran

Del Mar California

My Posts: All  Forum  Topic


reworking the trim around the windows

work being done to prepare for nose light installation

flying is the easy part paying for it whole different story

PM  EMAIL  HOMEPAGE  GALLERY  Attn:RR  Quote
05-05-2009 07:56 AM  9 years agoPost 5
James

rrVeteran

Del Mar California

My Posts: All  Forum  Topic

re working trim lines around the engine compartment doors.

putting down a thin coat of filler to make the bottom smooth lots and lots of sanding.

flying is the easy part paying for it whole different story

PM  EMAIL  HOMEPAGE  GALLERY  Attn:RR  Quote
05-05-2009 07:57 AM  9 years agoPost 6
James

rrVeteran

Del Mar California

My Posts: All  Forum  Topic

working the bottom

first primer coat

flying is the easy part paying for it whole different story

PM  EMAIL  HOMEPAGE  GALLERY  Attn:RR  Quote
05-05-2009 07:57 AM  9 years agoPost 7
James

rrVeteran

Del Mar California

My Posts: All  Forum  Topic


bottom sanded and primed plus painted flat black

front cockpit real smooth, painted flat black

flying is the easy part paying for it whole different story

PM  EMAIL  HOMEPAGE  GALLERY  Attn:RR  Quote
05-05-2009 07:57 AM  9 years agoPost 8
James

rrVeteran

Del Mar California

My Posts: All  Forum  Topic

front aluminum plates on full size G Jive

Rear aluminum plates

flying is the easy part paying for it whole different story

PM  EMAIL  HOMEPAGE  GALLERY  Attn:RR  Quote
05-05-2009 07:58 AM  9 years agoPost 9
James

rrVeteran

Del Mar California

My Posts: All  Forum  Topic


First stage of building up rear molding a lot of sanding and filing is required.

rear completed ready for priming

flying is the easy part paying for it whole different story

PM  EMAIL  HOMEPAGE  GALLERY  Attn:RR  Quote
05-05-2009 07:58 AM  9 years agoPost 10
James

rrVeteran

Del Mar California

My Posts: All  Forum  Topic

Rear and front moldings are seen with all three layers that are placed
on one at a time. Very time consuming but worth it. Seen with screw holes drilled.

showing rear and front molding plates completed and primed.

up coming pictures will be the nose light installed.

flying is the easy part paying for it whole different story

PM  EMAIL  HOMEPAGE  GALLERY  Attn:RR  Quote
05-05-2009 07:58 AM  9 years agoPost 11
James

rrVeteran

Del Mar California

My Posts: All  Forum  Topic

I may disappear for a while but that's because im doing a lot of work, since i have been gone. Here we go with more progress.

I decided to go all out. I have not really seen many fiber glass Hughes 500 be completely smooth on the inside not having to see any type of fiber glass cloth. Well it was a huge labor of love to do but it was worth it . There was so much small detailed, sanding around corners, and groves, that i sanded my finger nails, down so much from rubbing the sandpaper around that one finger started to bleed. I had to place tape on all of my finger tips Except for one finger, so i could check for smoothness.

Crazy i know that's what i had to do just so i could get the whole inside sanded and perfectly smooth. Here is the inside after i placed a thin coat of filler on the whole inside of fuselage it looks terrible but wait when you see the final results.

flying is the easy part paying for it whole different story

PM  EMAIL  HOMEPAGE  GALLERY  Attn:RR  Quote
05-05-2009 07:59 AM  9 years agoPost 12
James

rrVeteran

Del Mar California

My Posts: All  Forum  Topic

I decided to place a nose light, since the G Jive has one.

flying is the easy part paying for it whole different story

PM  EMAIL  HOMEPAGE  GALLERY  Attn:RR  Quote
05-05-2009 07:59 AM  9 years agoPost 13
James

rrVeteran

Del Mar California

My Posts: All  Forum  Topic

More pictures of the light. Im holding a picture, of the real Full size G jive. So you can tell i have placed it in the proper location.

flying is the easy part paying for it whole different story

PM  EMAIL  HOMEPAGE  GALLERY  Attn:RR  Quote
05-05-2009 07:59 AM  9 years agoPost 14
James

rrVeteran

Del Mar California

My Posts: All  Forum  Topic

check out the smoothness, of the interior. I am so glad i did the inside it gives a huge satisfaction seeing it this way. Instead of leaving the inside all full of fiber glass cloth imprints all over the place.

PS i did have the inside painted flat black but when i recieved a picture of the interior of the G jive it's a dark grey. So i changed the color to be more acurate .

flying is the easy part paying for it whole different story

PM  EMAIL  HOMEPAGE  GALLERY  Attn:RR  Quote
05-05-2009 07:59 AM  9 years agoPost 15
James

rrVeteran

Del Mar California

My Posts: All  Forum  Topic

Next thing i noticed was the G Jive has a small tear drop underneath it's boom which is used for small electrical connections inside. So i made a duplicate one by hand.

flying is the easy part paying for it whole different story

PM  EMAIL  HOMEPAGE  GALLERY  Attn:RR  Quote
05-05-2009 08:00 AM  9 years agoPost 16
James

rrVeteran

Del Mar California

My Posts: All  Forum  Topic

I noticed there is a large thick hook at the end of the tail fin, to protect from any rear rotor ground strike. I made one for my G Jive, I attached a picture, of the real one. The one i made has the same diameter, and curvature, but mine is a little longer then the real tail hook. I could have shorten it but for some reason, i like the one i made. So i am keeping it that way . It's close enough to scale look for me.

flying is the easy part paying for it whole different story

PM  EMAIL  HOMEPAGE  GALLERY  Attn:RR  Quote
05-05-2009 08:00 AM  9 years agoPost 17
James

rrVeteran

Del Mar California

My Posts: All  Forum  Topic

there is a small vent that is only on one side of the helicopter it's on the pilot side only. I attached a picture, of the real one and pictures, of the one i duplicated. I think it turned out real good.

flying is the easy part paying for it whole different story

PM  EMAIL  HOMEPAGE  GALLERY  Attn:RR  Quote
05-05-2009 08:00 AM  9 years agoPost 18
James

rrVeteran

Del Mar California

My Posts: All  Forum  Topic

I can see clearly there are foot sapports on the skids. So i made some out of stainless steel and placed them in the proper location.

flying is the easy part paying for it whole different story

PM  EMAIL  HOMEPAGE  GALLERY  Attn:RR  Quote
05-05-2009 08:00 AM  9 years agoPost 19
James

rrVeteran

Del Mar California

My Posts: All  Forum  Topic

I noticed the G Jive has handles inside of the doors, so i made some from scrach. I think they turned out ok. I was told they are made from rope which they are. These ones i found out have a vinyl, or plastic, coating over them making them more stiffer to look more like a handle but they do flex. mine on the other hand do not flex but thats ok it's the effort that counts i think.

flying is the easy part paying for it whole different story

PM  EMAIL  HOMEPAGE  GALLERY  Attn:RR  Quote
05-05-2009 08:01 AM  9 years agoPost 20
James

rrVeteran

Del Mar California

My Posts: All  Forum  Topic

I have done a lot of work on this cockpit. I have added a lot of small details, i will probably add more revit work to the inside. If i do i will post another picture, of anything i do. I will be having the cockpit, control gages light up when the doors open up. I have attached a picture of the gadges all lit up it's pretty cool.

Any comments are apreciated it keeps me going on this project.

flying is the easy part paying for it whole different story

PM  EMAIL  HOMEPAGE  GALLERY  Attn:RR  Quote
WATCH
 18 pages [ <<    <    ( 1 )     2      3     NEXT    >> ] 48637 views POST REPLY
HomeScaleAircraftHelicopterScale Model RC Helicopters Sell  *****SOLD ***** My Hughes MD 500 G Jive
 Print TOPIC  Make Suggestion 

 26  Topic Subscribe

Sunday, July 15 - 10:21 pm - Copyright © 2000-2018 RunRyder   EMAILEnable Cookies

Login Here
 New Subscriptions 
 Buddies Online